Catálogos >
Sea Hawk >
Cukote Biocide

Cukote Biocide
1 / 2Páginas

Excertos do catálogo

CUKOTE BIOCIDE Self-Polishing Copolymer Antifoulant Self-Polishing with Slime Resistance High Quality Multi-Season Performance Self-Polishing Coating Eliminates Heavy Buildup of Bottom Paint May Be Taken In and Out of Water Without Affecting Properties Harder Self-Polishing for Higher Speeds 3500 Series Product Description Following in the footsteps of the acclaimed Cukote self-polishing antifouling, Cukote Biocide Plus (adapting newer technology) has a high cuprous oxide content, combined with an organic algaecide – offering unprecedented control over all types of fouling, even in the most severe fouling areas. Cukote Biocide Plus‟ unique controlled erosion minimizes coating buildup and keeps underwater surfaces smooth and clean. Features and Benefits Product Information Colors Available: Black-3545, Dark Blue-3530, Blue-3542, Red3541, Green-3522 Finish/Sheen: Semi-Gloss Converter: One Pack Copper Content: 47.57% All Colors Volume Solids: 54% (±2%) Mix Ratio: One Pack Shipping Weight: 18-20 Lbs./Gal. Flash Point: 100°F VOC: 288 Grams/Liter Typical Film Thickness: Pleasure Craft: 2.5 mils dry film thickness (DFT) per coat by roller application (5.0 mils wet film thickness (WFT) Commercial Marine: Average 4.0-5.0 mils DFT per coat by spray application (7.5-9.0 mils WFT) Theoretical Coverage: 173 Sq.Ft. @ 5.0 mils DFT, 346 Sq. Ft. @ 2.5 mils Recommended Coats: 2 Full Coats with 3 at the water line and other high wear areas, depending on intended service. Self Polishing Ablative with Multi-Season Performance on Both Pleasure Craft, Coastal and Deep Sea Vessels Harder Ablative Finish Makes Cukote Biocide Ideal for Fast Moving Vessels including: Pleasure Craft Power Boats, High Speed Transports, Supply Vessels, and Ferries May Be Taken In and Out of the Water Without Affecting Antifouling Characteristics Does Not Contain Any Organotin Compounds (TBT) May Be Used on All Steel, Fiberglass, and Wood Vessels Below the Waterline That Have Been Planned Drydockings of Less Than Three Years Application Controls Method: Airless and Conventional Spray, Solvent Resistant Rollers and Brushes. Pleasure Craft Drying time in Hours Substrate Temp. Touch Min Max Launch 41°F (5°C) N/A N/A N/A N/A 73°F (23°C) 2 hr 1 hr N/A 12 hrs 95°F (35°C) 1 hr 1 hr N/A 12 hrs Limitations: Apply in good weather when air and surface temperatures are above 50°F (10°C). Surface temperature must be a least 50°F (10°C) above dew point. For optimum application properties, bring material to 70-80°F (21-27°C) temperature range prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage between 40° and 100°F (4-38°C). Prolonged atmospheric exposure of this product may detract from performance. Technical and application data herein is for the purpose of establishing a general guideline of the coating and proper coating application procedures. As application, environmental and design factors can vary significantly due care should be exercised in th e selection, verification of performance, and use of the coating. NEW NAUTICAL COATINGS, INC. 14805 49th Street North • Clearwater, FL 33762 • 727.523.8053 • 800.528.0997 • FAX 727.523.7325 www.SeaHawkPaints.com

Abrir o catálogo na página 1

CUKOTE BIOCIDE Surface Preparation Paint only clean, dry surfaces. Remove all grease, oil, wax, or other foreign material by solvent or detergent washing. (SSPC-SPI) Self-Polishing with Slime Resistance 3500 Series Compatibility: For pleasure craft applications, please refer to our Sea Hawk Compatibility Chart to ensure compatibility when applying Cukote Biocide antifouling paint over existing bottom paint. Previously Painted Surfaces: Cukote Biocide is suitable for this substrate. For correct procedures please refer to the Application Guidelines for Fiberglass/Gelcoat. Fiberglass or Vinyl...

Abrir o catálogo na página 2