JC3000 Finger Operated Joystick Controller
1 / 12Páginas

JC3000 FINGER OPERATED JOYSTICK CONTROLLER Innovation In Motion

INNOVATION IN MOTION The JC3000 joystick controller is designed for demanding applications in remote control chestpacks or auxiliary functions on industrial vehicles and other man-machine interfaces, where precise control, signal reliability, and compact size are important. The joystick is available with single or dual axis control, and can be specified with a choice of either long life potentiometer tracks, or switched output signals. Innovative design With a choice of potentiometer tracks that provide the analog signals proportional to lever movement or 3, 4 or 5 switched outputs per...

Potentiometric sensing Designed to interface with an electronic controller, the long-life potentiometer track generates analog outputs with switched reference signals that are proportional to the distance and direction over which the handle is moved. The analog output can be configured to provide signals for fault detection circuits, and a center tap provides an accurate voltage reference for the center position or a zero point for a bipolar supply voltage. The electrically independent switch operates with separate contacts each side of the joystick center position, in each available axis....

Lever operating torque XY 0.6 (full lever deflection at ±31°) Lever detent torque XY Lever breakout torque XY Maximum allowable torque XY Nm Lever operating angle 12.5 to 20 (full lever deflection, depending on gate and detent options selected) ±31 max. in X and Y directions (Actual angle will depend on gate selected) Lever action Self centering, aligned X and Y Lever gate profiles Single axis in X or Y, square or plus Lever angle Gate Code Track Code Detent angles Maximum Z axis torque Expected life Weight 205 nominal, without handle fitted ENVIRONMENTAL Operating temperature Storage...

ELECTRICAL CONNECTIONS All potentiometer track and directional/center/handle switch connections terminate in a 12-way Hirose DF3-12P-2DS(01) series connector on each joystick axis – a mating connector and flylead is available (one is required for each axis). The connectors used on the JC3000 joystick are gold plated, therefore the mating connectors should also be gold plated. Mating 12-way connector and flyleads Y-Axis Allocation X-Axis Allocation Wire Colour Output voltage signal Output voltage signal Switch track N/O (lever forward +Y) Switch track N/O (lever right +X) Normally not...

Lever operating torque XY 0.6 (full lever deflection at ±31°) Lever detent torque XY Lever breakout torque XY Maximum allowable torque XY Nm 12.5 to 20 (full lever deflection, depending on gate and detent options selected) Lever operating angle ±31 max. in X and Y directions (Actual angle will depend on gate selected) Self centering, aligned X and Y Lever action Single axis in X or Y, Square or Plus Lever gate profiles Lever angle Gate Code Track Code Detent angles Maximum Z axis torque 205 nominal, without handle fitted ENVIRONMENTAL Operating temperature Storage temperature -40 to +85...

ST O J C 3 0 0 0 JSOYI TC IHCEKD CO UNTTPRUO L L E R W T ELECTRICAL CONNECTIONS All switch track/center/handle switch connections terminate in a 12-way Hirose DF3-12P-2DS(01) series connector on each joystick axis – a mating connector & flylead is available (one is required for each axis). The connectors used on the JC3000 joystick are gold plated, therefore the mating connectors should also be gold plated. Mating 12-way connector and flyleads Y-Axis Allocation X-Axis Allocation Wire Colour Switch track common Switch track common Switch 1 (lever forward +Y) Switch 1 (lever right +X) Switch...

DIMENSIONS Note: drawings not to scale 40.00 ±0.05 Mounting detail Holes to suit M3 screws Forward orientation feature on casting HLO handle shown (see page 10 for alternatives) Xº Lever angle (Xº) depends on gate selected. 5.0 nominal (mounting flange to pivot) The joystick is designed to be fitted from below the mounting panel, through a 50.75/51.00mm diameter hole. The effectiveness of the joystick flange sealing is dependent on the panel mounting surface being sufficiently rigid to compress the sealing gaiter. The surface finish of the mounting panel is critical to achieving an adequate...

PERFORMANCE OPTIONS Single axis in Y direction only - Forward/Backward Single axis in X direction only - Right/Left Dual axis Single axis with ±31º lever range Selecting the gate style and angle determines the track code for switched output and 2/3 of the final track code for analog output versions. Single axis with ±25º lever range Single axis with ±19º lever range (Track code = P–5 or SW5) (Track code = P–4 or SW4) (Track code = P–3 or SW3) Square with ±31º lever range in X and Y Square with ±25º lever range in X and Y Square with ±19º lever range in X and Y Plus with ±31º lever range...

No handle, plain lever ø6.35 ±0.006 M5 thread No handle, M5 threaded lever K10 This handle option is a simple tapered style with no switch functions, allowing simple fingertip control. This handle option is a spherical ball style with no switch functions, allowing simple ‘finger and thumb’ control The handle has a recessed diametral groove on the circumference to aid grip. This handle option is a low profile, fluted style that has a maximum 59.2mm height above the mounting panel. This option allows closer spacing of multiple joysticks within a small surface area - typically in applications...

A switch function can be incorporated by using the ZC1 external button switch or the ZCS internal switch to verify the change in signals from the joystick. Press to activate switch PERFORMANCE Maximum height above flange mm Maximum diameter mm Environmental sealing (IEC 60529) Number of switches Action Switch operating force Maximum current Expected electrical life Switch connections terminate on the Hirose DF3 series connector. Actual pin allocation depends on the joystick track type and gate selection. See page 5 for Analog Output version connections. See page 7 for Switched Output...