Catálogos >
International Marine >
Interspeed 6400

Interspeed 6400
1 / 4Páginas

Excertos do catálogo

Interspeed 6400 TBT Free CDP Antifouling PRODUCT DESCRIPTION TBT free, controlled depletion polymer (CDP) self polishing antifouling system. INTENDED USES For use at Newbuilding or Maintenance & Repair. In repair situations Interspeed 6400 can be applied directly over existing antifoulings. PRODUCT INFORMATION Colour BQA644-Red, BQA648-Brown, BQA642-Blue, BQA643-Green, BQA649Black Finish/Sheen Not applicable Part B (Curing Agent) Not applicable Volume Solids 60% ±2% (ISO 3233:1998) Mix Ratio Not applicable Typical Film Thickness Range: 75 - 150 microns dry (125 - 250 microns wet) may be specified depending upon end use. Theoretical Coverage Range: 8.0 - 4.0 m²/litre at 75 - 150 microns dft, allow appropriate loss factors Method of Application Airless Spray, Brush, Roller Flash Point Single Pack 27°C Drying Information 5°C 10°C 25°C 35°C Touch Dry [ISO 9117/3:2010] 4 hrs Before Flooding 24 hrs 3.5 hrs 2 hrs 60 mins 20 hrs 12 hrs 12 hrs 5°C 10°C Overcoating Data - see limitations Substrate Temperature 25°C 35°C Overcoated By Min Max Min Max Min Max Min Max Interspeed 6400 12 hrs 6 mths 10 hrs 6 mths 6 hrs 6 mths 4 hrs 3 mths Note Overcoating data refers to BQA648 followed by BQA644. REGULATORY DATA VOC 363 g/lt as supplied (EPA Method 24) 210 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. This product does not contain organotin compounds acting as biocides and as such is in compliance with the International Convention on the Control of Harmful Anti-fouling Systems on ships as adopted by IMO in October 2001 (IMO document AFS/CONF/26). Marine Coatings Page 1 of 4 Issue Date:23/08/2011 Ref:4511

Abrir o catálogo na página 1

Interspeed 6400 TBT Free CDP Antifouling SYSTEMS AND COMPATIBILITY Consult your International Paint representative for the system best suited for the surfaces to be protected. SURFACE PREPARATIONS Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. NEWBUILDING Dependent on yard procedures. Consult International...

Abrir o catálogo na página 2

Interspeed 6400 TBT Free CDP Antifouling APPLICATION Mixing This material is a one pack coating and should always be mixed thoroughly with a power agitator before application. Thinner Not recommended. Use International GTA007 only in exceptional circumstances. DO NOT thin more than allowed by local environmental legislation. Airless Spray Recommended Tip Range 0.66-0.79 mm (26-31 thou) Total output fluid pressure at spray tip not less than 176 kg/cm² (2500 p.s.i.) Conventional Spray Application by conventional spray is not recommended. Brush Application by brush is recommended for small...

Abrir o catálogo na página 3

Interspeed 6400 TBT Free CDP Antifouling LIMITATIONS If the following maximum recommended exposure times before flooding are exceeded, antifouling performance may be impaired: Temperate conditions - 6 months, Tropical conditions - 3 months On immersion Interspeed 6400 changes colour. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of the surface to be coated must be at least...

Abrir o catálogo na página 4