Catálogos >
International Marine >
Intersmooth 7465Si SPC

Intersmooth 7465Si SPC
1 / 4Páginas

Excertos do catálogo

Intersmooth 7465Si SPC TBT Free, Low Friction, Self Polishing Copolymer A/F PRODUCT DESCRIPTION A high solids, high performance, TBT free, low friction, self polishing copolymer (SPC) antifouling. Based on patented Silyl Acrylate polymer technology. Particularly suitable for use where solvent emmissions need to be reduced. INTENDED USES Specifically designed for Deep Sea Vessels. For use at Newbuilding or Maintenance & Repair. PRODUCT INFORMATION Colour BEA814-Brown, BEA817-Red Note: The above codes will be substituted by BEA834-Brown and BEA837-Red when supplied from Felling, Dammam and Bangalore manufacturing locations. Finish/Sheen Not applicable Part B (Curing Agent) Not applicable Volume Solids 55% ±2% (ISO 3233:1998) Mix Ratio Not applicable Typical Film Thickness Range: 75 - 150 microns dry (136 - 273 microns wet) may be specified depending upon end use. Theoretical Coverage Range: 7.3 - 3.6 m²/litre at 75 - 150 microns dft, allow appropriate loss factors Method of Application Airless Spray, Brush, Roller Flash Point Single Pack 24°C Induction Period Not applicable Drying Information -5°C 5°C 25°C 35°C Touch Dry [ISO 9117/3:2010] 2 hrs 60 mins 40 mins 30 mins Before Flooding Single Coat 30 hrs 18 hrs 12 hrs 7 hrs Before Flooding Multiple Coats 48 hrs 36 hrs 24 hrs 12 hrs Note For Major Refurbishment and Repair if total dft is >300µm flood times must be increased as follows: 48 hours at 5°C, 36 hours at 25°C and 24 hours at 35°C. Overcoating Data - see limitations Substrate Temperature -5°C Overcoated By Intersmooth 7465Si SPC REGULATORY DATA VOC 5°C 25°C 35°C Min Max Min Max Min Max Min Max 12 hrs 6 mths 6 hrs 6 mths 5 hrs 6 mths 4 hrs 6 mths 394 g/lt as supplied (EPA Method 24) 210 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. This product does not contain organotin compounds acting as biocides and as such is in compliance with the International Convention on the Control of Harmful Anti-fouling Systems on ships as adopted by IMO in October 2001 (IMO document AFS/CONF/26). Marine Coatings Page 1 of 4 Issue Date:22/12/2011 Ref:4631

Abrir o catálogo na página 1

TBT Free, Low Friction, Self Polishing Copolymer A/F SURFACE PREPARATIONS Consult your International Paint representative for details. Consult your International Paint representative for the system best suited for the surfaces to be protected. Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. Intersmooth 7465SÌ...

Abrir o catálogo na página 2

Intersmooth 7465Si SPC TBT Free, Low Friction, Self Polishing Copolymer A/F APPLICATION Mixing This material is a one pack coating and should always be mixed thoroughly with a power agitator before application. Thinner Not Recommended. Use International GTA007 only in exceptional circumstances (max 5% by volume). DO NOT thin more than allowed by local environmental legislation. Airless Spray Recommended Tip Range 0.54-0.80 mm (21-31 thou) Total output fluid pressure at spray tip not less than 190 kg/cm² (2700 p.s.i.) Conventional Spray Application by conventional spray is not recommended....

Abrir o catálogo na página 3

Intersmooth 7465Si SPC TBT Free, Low Friction, Self Polishing Copolymer A/F LIMITATIONS UNIT SIZE Coating lifetime is directly proportional to thickness applied. Performance of the product is dependent upon the specified film thickness being achieved. On immersion, Intersmooth 7465Si SPC will exhibit a slight colour change. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of...

Abrir o catálogo na página 4