Catálogos >
International Marine >
Intersleek 970

Intersleek 970
1 / 4Páginas

Excertos do catálogo

Intersleek 970 Fluoropolymer Foul Release Coating PRODUCT DESCRIPTION A three pack, fluoropolymer foul release coating. INTENDED USES As the finishing coat in the Intersleek 900 foul release system. For use at Newbuilding or Maintenance & Repair. PRODUCT INFORMATION Colour FXA970-White, FXA971-Grey, FXA972-Blue, FXA977-Red, FXA979-Black; and a limited range of colours Finish/Sheen Gloss Part B (Curing Agent) FXA980 (Part B), FXA981 (Part C) Volume Solids 74% ±2% (ISO 3233:1998) Mix Ratio 16 volume(s) Part A to 3 volume(s) Part B to 1 volume(s) Part C Typical Film Thickness Range: 150 - 200 microns dry (203 - 270 microns wet) may be specified depending upon end use. Theoretical Coverage Range: 4.93 - 3.70 m²/litre at 150 - 200 microns dft, allow appropriate loss factors Method of Application Airless Spray, Brush Flash Point Part A 38°C; Part B 24°C; Part C 32°C; Mixed 32°C Induction Period Not required Drying Information 0°C 15°C 25°C 35°C Touch Dry [ISO 9117/3:2010] 7 hrs 4 hrs 3 hrs 2 hrs Hard Dry [ISO 9117-1:2009] 16 hrs 9 hrs 6 hrs 5 hrs Before Flooding 48 hrs 36 hrs 20 hrs 17 hrs 140 mins 90 mins 60 mins 30 mins Pot Life Note The interval prior to flooding may be reduced to 24 hours at temperatures between 5°C and 20°C provided that the ship remains at rest for a minimum period of 2-3 days after flooding. At temperatures between 0°C and 5°C, the absolute minimum time to flooding is 48 hours and the ship must remain at rest for a minimum of 4 days after undocking. However, the coating may suffer intercoat detachment in any areas that are subject to mechanical abrasion due to, eg. fendering or impact damage. Overcoating Data - see limitations Substrate Temperature 0°C Overcoated By Note REGULATORY DATA Min 15°C Max Min 25°C Max Min 35°C Max Min Max May be overcoated by self, either when fresh or after prolonged immersion provided surface is in good, clean condition. Consult International Paint. Intersleek 970 CANNOT be overcoated by Intersleek 757. VOC 248 g/lt as supplied (EPA Method 24) 241 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. This product does not contain organotin compounds acting as biocides and as such is in compliance with the International Convention on the Control of Harmful Anti-fouling Systems on ships as adopted by IMO in October 2001 (IMO document AFS/CONF/26). Marine Coatings Page 1 of 4 Issue Date:23/09/2011 Ref:3782

Abrir o catálogo na página 1

Intersleek 970 Fluoropolymer Foul Release Coating CERTIFICATION When used as part of an approved scheme, this product has the following certification: Product recognised by the following classification societies as compliant with the International Convention on the Control of Harmful Anti-fouling Systems on Ships, 2001 (AFS 2001): • • • • • Lloyds Register Det Norske Veritas Korean Register of Shipping Bureau Veritas Germanischer Lloyd Consult your International Paint representative for details. SYSTEMS AND COMPATIBILITY Consult your International Paint representative for the system best...

Abrir o catálogo na página 2

Fluoropolymer Foul Release Coating Airless Spray Conventional Spray Work Stoppages and Cleanup Material is supplied in 3 containers as a unit. Always mix a complete unit in the proportions supplied. (1) Agitate Part A with a power agitator. (2) Combine entire contents of Part A and Part B and mix thoroughly with a power agitator. (3) Add entire contents of Part C and mix thoroughly with a power agitator. Not recommended. Use International GTA007 only in exceptional circumstances. DO NOT thin more than allowed by local environmental legislation. Total output fluid pressure at spray tip not...

Abrir o catálogo na página 3

Intersleek 970 Fluoropolymer Foul Release Coating LIMITATIONS Minimum acceptable substrate temperature at the time of application is 0°C. A minimum Relative Humidity of 30% is required to ensure satisfactory curing. Longer cure times will be required if the Relative Humidity falls below 30%. Care should be taken to avoid overspray onto other coated areas. Intersleek 970 must be applied over Intersleek tie coat within the required overcoating interval. All equipment must be thoroughly clean prior to use, and before re-use with other materials, to prevent contamination. Liquid cleaners for...

Abrir o catálogo na página 4