Catálogos >
International Marine >
Intersleek 386

Intersleek 386
1 / 4Páginas

Excertos do catálogo

Intersleek 386 Elastomeric Tie Coat PRODUCT DESCRIPTION A three pack, silicone elastomer foul release tie coat. INTENDED USES To promote adhesion between the specified priming system and the Intersleek 425 finish coat. Also used as the primer for Intersleek 425 finish coat on rubber substrates. For use at Newbuilding or Maintenance & Repair. PRODUCT INFORMATION Colour BXA385-Pink (Part A), BXA386-Light Grey (Part A) Finish/Sheen Not applicable Part B (Curing Agent) BXA390 (Part B), BXA391 (Part C) Volume Solids 57% ±2% (ISO 3233:1998) Mix Ratio 4 volume(s) Part A to 5 volume(s) Part B to 1 volume(s) Part C Typical Film Thickness 100 microns dry (175 microns wet) Theoretical Coverage 5.70 m²/litre at 100 microns dft, allow appropriate loss factors Method of Application Airless Spray, Brush, Roller Flash Point Part A 36°C; Part B 38°C; Part C 25°C; Mixed 28°C Induction Period Not required Drying Information 5°C 15°C 25°C 35°C Touch Dry [ISO 1517:73] 5 hrs 3 hrs 2 hrs 60 mins Hard Dry [ISO 9117:90] 10 hrs 7 hrs 5 hrs 3 hrs 140 mins 90 mins 60 mins 30 mins 5°C 15°C Pot Life Overcoating Data - see limitations Overcoated By Intersleek 425 REGULATORY DATA VOC Substrate Temperature 25°C 35°C Min Max Min Max Min Max Min Max 22 hrs 7 days 18 hrs 7 days 12 hrs 7 days 6 hrs 7 days 377 g/lt as supplied (EPA Method 24) 280 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC) Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. Marine Coatings Page 1 of 4 Issue Date:23/02/2010 Ref:144

Abrir o catálogo na página 1

Intersleek 386 Elastomeric Tie Coat SYSTEMS AND COMPATIBILITY Consult your International Paint representative for the system best suited for the surfaces to be protected. SURFACE PREPARATIONS Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. Intersleek 386 should always be applied over a recommended coating...

Abrir o catálogo na página 2

Mixing Material is supplied in 3 containers as a unit. Always mix a complete unit in the proportions supplied. (1) Agitate Part A with a power agitator. (2) Combine entire contents of Part A and Part B and mix thoroughly with a power agitator. (3) Add entire contents of Part C and mix thoroughly with a power agitator. Once the unit has been mixed, it must be used within the working pot life specified. Not recommended. Use International GTA007 only in exceptional circumstances. DO NOT thin more than allowed by local environmental legislation. Total output fluid pressure at spray tip not less...

Abrir o catálogo na página 3

Intersleek 386 Elastomeric Tie Coat LIMITATIONS Minimum acceptable substrate temperature at the time of application is +5°C. A minimum Relative Humidity of 30% is required to ensure satisfactory curing. Longer cure times will be required if the Relative Humidity falls below 30%. Care should be taken to avoid overspray onto other coated areas. Precautions should be taken to prevent silicone contamination of adjacent areas. All equipment must be thoroughly clean prior to use, and before re-use with other materials, to prevent contamination. Liquid cleaners for Intersleek 386 must not be...

Abrir o catálogo na página 4