Catálogos >
International Marine >
INTERSHIELD 300 DATA SHEET

INTERSHIELD 300 DATA SHEET
1 / 4Páginas

Excertos do catálogo

Abrasion Resistant Aluminium Pure Epoxy PRODUCT DESCRIPTION INTENDED USES PRODUCT INFORMATION A light coloured, abrasion resistant, aluminium pure epoxy coating giving excellent long term anticorrosive protection and low temperature application capability. A universal primer which can be applied directly to mechanically prepared shop primer or suitably prepared bare steel. Suitable for use with controlled cathodic protection. For use at Newbuilding or Maintenance & Repair. Part B (Curing Agent) Volume Solids Typical Film Thickness Theoretical Coverage Flash Point Induction Period 2.50 volume(s) Part Ato 1 volume(s) Part B 4.00 nfVlitre at 150 microns dft, allow appropriate loss factors Airless Spray, Brush, Roller Part A 28°C; Part B 26°C; Mixed 28°C Drying Information Note See Limitations section when Intershield 300 is used as part of an Intersleek scheme. Overcoating Data - see limitations Substrate Temperature Immersed Areas Note When overcoating with Intersleek 386, refer to the Intersleek 737 data. Intershield 300 may be overcoated with Intersleek 737 at 0°C, the minimum interval being 12 hours and the maximum 30 hours. Intershield 300 may be overcoated with Intersleek 731 above 20°C. At 20°C, the minimum interval being 5 hours and the maximum When overcoating with Interbond 201 or Interbond 501, referto the Intergard 740 data. Interthane 990 may be used on boottop areas at reduced overcoating intervals. Consult International Paint. Interfine 691 is currently only available in Europe. REGULATORY DATA 318 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances. Marine Coatings

Abrir o catálogo na página 1

Abrasion Resistant Aluminium Pure Epoxy SURFACE PREPARATIONS When used as part of an approved scheme, this product has the following certification: Food Contact - Carriage of Grain (NOHA) Tank Coatings - Recognised Corrosion Control Coating (LR) Tank Coatings - B1 Classification of Ballast Tank Coatings (DNV/Marintek tested) Tank Coatings - Ballast Tank type approval (GL) Tank Coatings - NORSOK M-501, Rev 3, system 7 (Marintek) Fire Resistance - MSC61(67) Smoke & Toxicity (WFR) Fire Resistance - Surface Spread of Flame (WFR) - (IMO Resolution A653 (16)) Fire Resistance - Marine Equipment...

Abrir o catálogo na página 2

Abrasion Resistant Aluminium Pure Epoxy Airless Spray Work Stoppages and Cleanup Material is supplied in two containers as a unit. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified. (1) Agitate Base (Part A) with a power agitator. (2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator. Use International GTA220 only in exceptional circumstances. DO NOT thin more than allowed by local environmental legislation. Total output fluid pressure at spray...

Abrir o catálogo na página 3

Il IIWI I lUllVl Idi® Abrasion Resistant Aluminium Pure Epoxy LIMITATIONS Intershieid 300 should be high pressure fresh water washed and/or solvent washed prior to overcoating, where necessary, to ensure removal of any surface contamination that has accumulated. Suitable for use on tanker decks subject to Classification Society Regulations. Intershieid 300 may be applied at substrate temperatures down to -15°C. Before applications are made below -5°C consult your local IP representative for further detail of application procedure. When Intershieid 300 is to be overcoated with Intersleek...

Abrir o catálogo na página 4