Catálogos >
International Marine >
INTERGARD 5600 DATA SHEET

INTERGARD 5600 DATA SHEET
1 / 4Páginas

Excertos do catálogo

PRODUCT DESCRIPTION A light colored, epoxy universal primer. Modified Epoxy INTENDED USES PRODUCT INFORMATION For use as an anticorrosive universal primer in ballast tanks, outer hull, cofferdams, void spaces, decks, cargo holds Suitable for use with controlled cathodic protection. For use at Newbuilding or Maintenance & Repair. Part B (Curing Agent) Volume Solids Typical Film Thickness Theoretical Coverage Flash Point 4.00 volume(s) Part A to 1 volume(s) Part B 170 ft2/US gal at 6.4 mils dft, allow appropriate loss factors Airless Spray, Brush, Roller Part A 79°F; Part B 91 °F; Mixed 81 °F Overcoating Data - see limitations Substrate Temperature Intergard 263 24 hrs 4 mths 16 hrs 4 mths 6 hrs 4 mths 4 hrs 3 mths Intergard 269 40 hrs 6 mths 30 hrs 6 mths 12 hrs 6 mths 6 hrs 5 mths Intergard 410 40 hrs 4 mths 30 hrs 4 mths 12 hrs 4 mths 6 hrs 3 mths Intergard 5600 40 hrs 28 days 30 hrs 28 days 12 hrs 28 days 6 hrs 21 days Immersed Areas Intergard 5600 40 hrs 4 mths 30 hrs 4 mths 12 hrs 4 mths 6 hrs 3 mths Intergard 740 24 hrs 28 days 18 hrs 28 days 6 hrs 28 days 4 hrs 21 days Interthane 990 40 hrs 5 days 30 hrs 5 days 12 hrs 5 days 6 hrs 3 days REGULATORY DATA 304 g/lt (2.54 lb/US gal) as supplied (EPA Method 24) Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances. Marine Coatings

Abrir o catálogo na página 1

Modified Epoxy SURFACE PREPARATIONS When used as part of an approved scheme, this material has the following certification: • Food Contact - Carriage of Grain (NOHA) • Fire Resistance - Marine Equipment Directive compliant • Fire Resistance - Surface Spread of Flame (WFR) - (IMO Resolution A653 (16)) Consult your International Paint representative for details. Consult your International Paint representative for the system best suited for the surfaces to be protected. Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated must be clean, dry and free...

Abrir o catálogo na página 2

Modified Epoxy Airless Spray Work Stoppages and Cleanup Material is supplied in 2 containers as a unit. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified. (1) Agitate Base (Part A) with a power agitator. (2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator. Not Recommended. Use International GTA220 only in exceptional circumstances (max 5% by volume). DO NOT thin more than allowed by local environmental legislation. Total output fluid pressure at...

Abrir o catálogo na página 3

Modified Epoxy This product will not cure adequately below 41 °F. For maximum performance, the curing temperature should be above 50°F. Drying times and overcoating intervals may alter due to on-site factors such as tank configuration or ventilation rates Intergard 5600 must not be used in mixed schemes with Intergard 5620. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate and environmental conditions. Consult your local International Paint representative for specific recommendations. Apply in good weather. Temperature of...

Abrir o catálogo na página 4