Satin Matt
1 / 3Páginas

Excertos do catálogo

Satin Matt - 1

Product Data Sheet Awlwood Satin Matt OJ3810 Intended Uses Awlwood Satin Matt is an exterior clear system that is made up of a Primer and Clear Satin Matt Finish. By combining the Primer and Clear together, the synergistic effect results in an outstanding performing system that adheres and bonds directly to the wood cellular structure giving extended performance and retaining the same gloss, DOI and natural appearance as first application. Specification Data Volume Solids Specific Gravity Available Packs Equipment Cleaning Typical Shelf Life 28% 1.02 1 US Quart, 1 US Gallon (EU & US only) Awlwood OT0200 Brush Cleaner 2 years Theoretical Coverage Application Methods Theoretical Coverage Per Coat (at recommended DFT) Brush, Roller Airless Spray Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size and application environment. VOC All VOC information contained herein is theoretical (unless otherwise stated). Actual VOC content may vary by batch and when tested via standard test methodology. Product As Supplied (without reducer) g/l Awlwood Satin Matt Surface Preparation Awlwood Satin Matt should be applied over a fully built system of Awlwood Gloss as the final coat only. Ideally at least 12 hours should elapse after the application of the last coat of Awlwood Gloss before coating with Awlwood Satin Matt. In cold temperatures, more time may be required. As a benchmark, the Awlwood Gloss should sand readily without clogging the paper before proceeding. Hand sanding through to P600 grit paper working with the grain to give a uniform dull finish will give best results. As the matting mechanism is shrinkage caused by solvent loss, any sanding marks or texture in the substrate will clearly show. Care should be taken to avoid sanding through multiple coats of Awlwood Gloss. This may show through in the cured coat of Awlwood Satin Matt. To remedy, best practice is to apply another full coat of Awlwood Gloss and carefully resand. After sanding, remove sanding dust by vacuuming then warm water wash only using lint free cloths until surface is completely clean. Tack cloths are not recommended. If contamination is suspected use the two rag technique to solvent wash the surface using only Awlwood Brush Reducer or Awlwood Spray Reducer before and after sanding. The surface preparation advice provided, and equipment suggestions, can be used as a guide. Preparation techniques and results will vary according to individual conditions, equipment choice/condition and other factors. Testing on a non-critical area should be carried out prior to full-scale preparation.Awlwood Satin Matt should be applied over a fully built system of Awlwood Gloss as the final coat only. Mixing & Reduction Product is single pack and a suitable viscosity for brushing, rolling and spraying directly from the can. It should never be thinned. If the viscosity is too high for easy application, the product is likely to have partially reacted with moisture and is unsuitable for use. Do not add universal, alcohol-based thinners/reducers or any other material into Awlwood Satin Matt as cure and longevity of the product will be severely compromised. Ensure that brushes washed with Awlwood Brush Cleaner are well rinsed with Acetone, Awlwood Brushing Reducer or Awlwood Spray Reducer before using with Awlwood Satin Matt FOR FURTHER DETAILED INFORMATION AND ADVICE ABOUT THE AWLWOOD SYSTEM REFER TO THE AWLWOOD TECHNICAL APPLICATION BROCHURE. Mixing and reduction requirements will vary according to individual conditions, climate, equipment choice/condition and other factors. Mixing and application of a small sample before full scale application is recommended. Application Please refer to your local representative or visit http://www.awlgrip.com foras a guide. Actual equipment choices will vary according to application conditions, equipment Application equipment and parameters are given further information. choice/condition and other factors. Testing on a non-critical area should be carried out prior to full-scale application. Contact your local technical service Awlgrip, the AkzoNobel logo and other products mentioned in this publication are trademarks of AkzoNobel. ©AkzoNobel 2015 representative for further advice if necessary. 1 of 3 Ref:10376 Awlwood Satin Matt - Invert can and shake well in a twisting action prior to use Suitable application conditions: 10ºC 30ºC, Relative humidity 30% 90% - Do not apply when conden

Abrir o catálogo na página 1
Satin Matt - 2

compromised. Ensure that brushes washed with Awlwood Brush Cleaner are well rinsed with Acetone, Awlwood Brushing Reducer or Awlwood Spray Reducer before using with Awlwood Satin Matt Product Data Sheet FOR FURTHER DETAILED INFORMATION AND ADVICE ABOUT THE AWLWOOD SYSTEM REFER TO THE AWLWOOD TECHNICAL APPLICATION BROCHURE. Awlwood Satin Matt will vary according to individual conditions, climate, equipment choice/condition and other factors. Mixing and application Mixing and reduction requirements OJ3810 of a small sample before full scale application is recommended. Application Application...

Abrir o catálogo na página 2
Satin Matt - 3

Product Data Sheet Awlwood Satin Matt OJ3810 Warning Notes Please ensure a risk assessment is carried out to assess the level of PPE required for the particular task undertaken when using this product. Some sunscreens contain ‘nano grades’ of Titanium Dioxide or Zinc Oxide which when transferred from hands onto varnished exterior surfaces will accelerate UV degradation of the surface significantly. Coating Maintenance Do not attempt to cut and polish or wax Awlwood Satin Matt. Clean using warm water, detergent and a soft bristled brush then rinse well with fresh water. Avoid abrasive...

Abrir o catálogo na página 3

Todos os catálogos e folhetos Awlgrip

  1. Max Cor CF Primer

    2 Páginas

  2. 545

    2 Páginas

  3. AWLBRITRE

    2 Páginas

  4. Awlcare

    2 Páginas

  5. Awlcraft SE

    3 Páginas

  6. AWL®COAT TPC

    2 Páginas

  7. Wash Primer CF

    2 Páginas

  8. Griptex

    3 Páginas

  9. Awlgrip Topcoat

    2 Páginas

  10. Crater-X

    2 Páginas

  11. Awlfair LW

    3 Páginas

  12. Awlfair Pumpable

    2 Páginas

  13. Surface Cleaner

    2 Páginas

  14. D3200 D6200

    4 Páginas

  15. Awlcoat TPC

    2 Páginas

  16. Alumiprep 33

    1 Páginas

  17. Awlwood

    5 Páginas

  18. Awlcare

    2 Páginas

  19. Awlwash

    2 Páginas

  20. 345 HS PRIMER

    3 Páginas

  21. 321 HS UNDERCOAT

    3 Páginas

  22. Awlcraft SE

    3 Páginas

  23. Activators

    2 Páginas

  24. 345HS Primer

    3 Páginas

  25. Awlcraft 2000 VOC

    2 Páginas

  26. Pro-Cure

    2 Páginas

  27. REDUCERS

    3 Páginas

Catálogos arquivados

  1. AWL®COAT TPC

    2 Páginas

  2. AWLGRIP

    6 Páginas

  3. CF 2K

    3 Páginas