REDUCERS
1 / 3Páginas

Excertos do catálogo

REDUCERS - 1

PRODUCT DATA SHEET REDUCERS Topcoat – Special Purpose – Primer General Information All of the listed reducers for Awlgrip, Awlcraft 2000 and Awlcraft SE Topcoats can be blended with each other in any ratio to fine tune flow and evaporation rates. Most Awlgrip and Awlcraft 2000 Topcoats recommend up to 25% reduction. The reduction percentage is calculated from the combined total of the base component and converter component. Mixing a quart of base and a quart of converter yields 2 quarts of mixed base and converter: 25% would be 1/2 quart of reducer. Examples of total mix quantities for 1:1 and 2:1 base to converter ratios are as follows: 1:1 mix materials Awlgrip Topcoat Spray, 545 Primer, etc. Reduction: 25% Color Base 12 oz. Converter 12 oz. Reducer 6 oz. Total Mix 30 oz. 2:1 mix materials: Awlgrip Topcoat Brush (10-33% reduction), Awlcraft 2000 Topcoat Spray (up to 25% reduction) Reduction: 25% 30% 33% Color Base 12 oz. 12 oz. 12 oz. Converter 6 oz. 6 oz. 6 oz. Reducer 4.5 oz. 5.5 oz. 6 oz. Total Mix 22.5 oz. 23.5 oz. 24 oz. At higher temperatures, reducers evaporate faster. When painting in hot conditions increasing the amount of reducer in the mix by 510% will help compensate for this factor. Topcoat Reducers T0001 Fast Evaporating Reducer for Spray Applied Urethane Topcoats Use T0001 in Awlgrip/Awlcraft 2000/Awlcraft SE Topcoats when application and cure temperatures are between 60-75°F (16-24°C). At 60-75°F (16-24°C), T0001 will keep the paint film open for good flow but evaporate fast enough to provide adequate dry and dustfree times. VOC: 888 g/lt or 7.4 lbs/gallon T0002 Fast Evaporating Reducer and Equipment Cleaner Use T0002 in Awlgrip/Awlcraft 2000/Awlcraft SE Topcoats when application and cure temperatures are between 55-70°F (13-21°C). At 55-70°F (13-21°C), T0002 will keep the paint film open but evaporate fast enough to provide adequate dry and dust-free times. T0002 is also an excellent gun and equipment. T0002 can also be used in conjunction with T0005 at higher temperatures (> 90°F/32°C) to combat solvent popping. Use T0002 as the reducer for topcoats flattened with G3013 Flattening Agent and G2002 Awlgrip Flat Black for best finish development. VOC: 806 g/lt or 6.7 lbs/gallon T0003 Standard Reducer for Spray Applied Urethane Topcoats Use T0003 in Awlgrip, Awlcraft 2000 and Awlcraft SE Topcoats when application and cure temperatures are between 70–90°F (21–32°C). T0003 will keep the paint film open but evaporate fast enough to provide adequate dry and dust–free times. VOC: 2270 Morris Avenue • Union, New Jersey 07083 • USA • Tel: 888.355.3090 • Fax: 908.686.1752 Bannerlaan 54 • B-2280 Grobbendonk • Belgium • Intl. Tel: 32.14.257770 • Intl. Fax: 32.14.230880 76 Waterway Drive • Coomera • QLD 4209 • Australia • Tel: 61.7.5573.9655 or 1800.007.866 • Fax: 61.7.5573.9677 686 Rosebank Road • Avondale • Auckland • New Zealand • Tel: 64.9.828.3009 or 0800.150.527 • Fax: 64.9.828.1129 No.1 Tuas Avenue 4 • Singapore 639382 • Tel: 65.6862.2928 • Fax: 65.6862.0778 Page 1 of 3 • Rev 4 – NOV 2011 • Reducers for Primers and Topcoats

Abrir o catálogo na página 1
REDUCERS - 2

PRODUCT DATA SHEET REDUCERS Topcoat – Special Purpose – Primer T0005 Hot Weather Reducer for Urethane Topcoats Use T0005 in Awlgrip, Awlcraft 2000 and Awlcraft SE Topcoats when application and cure temperatures are 90–105°F (32–41°C). T0005 is most often used as an additive, blended with other spray reducers to improve flow. T0005 is seldom the sole reducer. At lower temperatures (below 90°F/32°C) T0005 can be blended at any ratio with other Awlgrip topcoat reducers to improve flow with those products or increase the evaporation rate of T0005. T0005 has a very slow evaporation rate; using...

Abrir o catálogo na página 2
REDUCERS - 3

PRODUCT DATA SHEET REDUCERS Topcoat – Special Purpose – Primer It should not be used in urethane or epoxy coatings. VOC: T0180 Spray Reducer for Awlspar Varnish T0180 is specially formulated as a spray reducer for Awlspar varnish. It should not be used in any urethane or epoxy coating. VOC: Primer Reducers T0001 Usually used in Awlgrip, Awlcraft 2000 and Awlcraft SE Topcoats. T0001 is also recommended for use in Quik-Grip Primer and Awlbrite Quik-Fil Clear. VOC: 888 g/lt or 7.4 lbs/gallon T0003 Usually used in spray applications of Awlgrip, Awlcraft 2000 and Awlcraft SE Topcoats. T0003 is...

Abrir o catálogo na página 3

Todos os catálogos e folhetos Awlgrip

  1. Max Cor CF Primer

    2 Páginas

  2. 545

    2 Páginas

  3. AWLBRITRE

    2 Páginas

  4. Awlcare

    2 Páginas

  5. Awlcraft SE

    3 Páginas

  6. AWL®COAT TPC

    2 Páginas

  7. Wash Primer CF

    2 Páginas

  8. Satin Matt

    3 Páginas

  9. Griptex

    3 Páginas

  10. Awlgrip Topcoat

    2 Páginas

  11. Crater-X

    2 Páginas

  12. Awlfair LW

    3 Páginas

  13. Awlfair Pumpable

    2 Páginas

  14. Surface Cleaner

    2 Páginas

  15. D3200 D6200

    4 Páginas

  16. Awlcoat TPC

    2 Páginas

  17. Alumiprep 33

    1 Páginas

  18. Awlwood

    5 Páginas

  19. Awlcare

    2 Páginas

  20. Awlwash

    2 Páginas

  21. 345 HS PRIMER

    3 Páginas

  22. 321 HS UNDERCOAT

    3 Páginas

  23. Awlcraft SE

    3 Páginas

  24. Activators

    2 Páginas

  25. 345HS Primer

    3 Páginas

  26. Awlcraft 2000 VOC

    2 Páginas

  27. Pro-Cure

    2 Páginas

Catálogos arquivados

  1. AWL®COAT TPC

    2 Páginas

  2. AWLGRIP

    6 Páginas

  3. CF 2K

    3 Páginas