Awlquik Epoxy Primer/Surfacer D8003/D9001
1 / 2Páginas

{{requestButtons}}

Excertos do catálogo

Awlquik Epoxy Primer/Surfacer D8003/D9001 - 1

PRODUCT DATA SHEET Awlquik Epoxy Primer/Surfacer D8003/D9001 Features & Uses A quick drying, medium build, easily sanded, two component epoxy primer/surfacer. Easy to apply by brush, roller or spray. Not to be used below the waterline. Specification Data Type: Epoxy Polyamide Packaging: Available in 1 gallon and 1 quart containers 2 Theoretical Coverage: Sq. Feet/Gallon: 609 Sq. Feet (57m ) at one mil dry (25 microns). 2 203-305 Sq. Feet (19-28m ) at recommended dry film thickness. Calculated for mixed base and converter reduced 50%. Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and application environment. Recommended Wet Film Thickness: 5 mils (125 microns) Recommended Dry Film Thickness: 2-3 mils (50-75 microns) Recoatability: At 77F/50% R.H. Spray: may be overcoated with itself, 4 hours; with 545 Primer or topcoat, 12 hours. Brush Roll: with itself, 12 - 14 hours, with other products 12 - 14 hours. Maximum without sanding: 24 Hours. May be overcoated with Awlgrip/Awlcraft 2000 Topcoats, and 545 Epoxy Primer. Note: Sealing Awlquik with 545 Primer before applying an Awlgrip/Awlcraft 2000 topcoat will maximize gloss and D.O.I. of the topcoat. VOC: Base (D8003) – 436 g/lt or 3.6 lbs/gallon Converter (D9001) – 354 g/lt or 3 lbs/gallon Application Equipment Conventional or airless spray and brush/roller. Airless Equipment Graco or Binks equivalent Spray gun: #95 Orifice Size: 028” – .043” Fan size & Angle: 8” – 80°, or 6” – 60° On a 25-1 pump, the input pressure gauge should read 70 to 80 lbs. On a 40-1 pump, the input pressure gauge should read 50 to 60 lbs. Pressure Pot Fluid nozzle: #63BSS (.046” Orifice size) Fluid needle: #663A Air nozzle: #63PW Pressure gauge should read 8-12 lbs. Atomizing pressure 50 to 60 lbs. All trademarks mentioned in this publication are owned by, or licensed to, the AkzoNobel group of companies. ©AkzoNobel 2015 Page 1 of 2 - Rev 5 – January 2015 - AWLQUIK

Abrir o catálogo na página 1
Awlquik Epoxy Primer/Surfacer D8003/D9001 - 2

PRODUCT DATA SHEET Awlquik Epoxy Primer/Surfacer D8003/D9001 Surface Preparation Best when used as a surfacer over other Awlgrip Primers. May be applied by brush or roller directly to properly prepared wood or fiberglass. Best results are obtained when these surfaces are first sealed with 545 Primer. Mixing and Reduction Spray: Mix by volume 1 part D8003 Base with 1 part D9001 until a smooth, homogenous mixture is obtained. Reduce as necessary up to 50% with Spray Reducer T0006 Example: 8 oz. D8003, 8 oz. D9001, 8 oz. T0006. Brush/Roll: Reduce mixed D8003/D9001 as needed up to 50% with...

Abrir o catálogo na página 2

Todos os catálogos e folhetos Awlgrip

  1. Max Cor CF Primer

    2 Páginas

  2. 545

    2 Páginas

  3. AWLBRITRE

    2 Páginas

  4. Awlcare

    2 Páginas

  5. Awlcraft SE

    3 Páginas

  6. AWL®COAT TPC

    2 Páginas

  7. Wash Primer CF

    2 Páginas

  8. Satin Matt

    3 Páginas

  9. Griptex

    3 Páginas

  10. Awlgrip Topcoat

    2 Páginas

  11. Crater-X

    2 Páginas

  12. Awlfair LW

    3 Páginas

  13. Awlfair Pumpable

    2 Páginas

  14. Surface Cleaner

    2 Páginas

  15. D3200 D6200

    4 Páginas

  16. Awlcoat TPC

    2 Páginas

  17. Alumiprep 33

    1 Páginas

  18. Awlwood

    5 Páginas

  19. Awlcare

    2 Páginas

  20. Awlwash

    2 Páginas

  21. 345 HS PRIMER

    3 Páginas

  22. 321 HS UNDERCOAT

    3 Páginas

  23. Awlcraft SE

    3 Páginas

  24. Activators

    2 Páginas

  25. 345HS Primer

    3 Páginas

  26. Awlcraft 2000 VOC

    2 Páginas

  27. Pro-Cure

    2 Páginas

  28. REDUCERS

    3 Páginas

Catálogos arquivados

  1. AWL®COAT TPC

    2 Páginas

  2. AWLGRIP

    6 Páginas

  3. CF 2K

    3 Páginas