Catálogos >
3M >
Cleaner C596 Primers

Cleaner C596 Primers
1 / 5Páginas

Excertos do catálogo

Adhesion Promoter/Primer 3M™ Adhesion Promoter AP596 3M™ Fritted Glass Primer P590 3M™ Plastic Primer P591 3M™ Metal Primer P592 3M™ Teak & Glass Primer P595 3M™ Teak & Glass Primer P597, Clear Technical Data Product Description 3M™ Adhesion Promoter AP596 and 3M™ Primers P590, P591, P592, P595 and P597 are low viscosity adhesion promoters recommended for use with the 3M™ 500-Series Polyurethane Adhesives/Sealants and 3M™ 700-Series Hybrid Adhesives/Sealants, as well as the 3M™ OEM Polyurethane Glass Adhesive Sealant 590. 3M Adhesion Promoter and Primers are applied to a wide variety of materials including glass, acrylic / PMMA, polycarbonate, and many other materials prior to adhesive/sealant use to assist in bonding. Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Technical Data 3M™ Adhesion Promoter AP596 Color Viscosity 3M™ Fritted Glass Primer P590 3M™ Teak & Glass Primer P595 3M™ Teak & Glass Primer P597, Clear Water Thin Water Thin 12 - 15 seconds 12 - 15 seconds (DIN Cup) (Ford Cup) Silane / Ethanol Silane / Ethanol Active Ingredient

Abrir o catálogo na página 1

3M™ Adhesion Promoter/Primer • Adhesion Promoter AP596 • Fritted Glass Primer P590 • Plastic Primer P591 • Metal Primer P592 • Teak & Glass Primer P595 • Teak & Glass Primer P597, Clear Performance Data The following table shows the impact in terms of adhesion strength of bonding common window substrates with and without 3M™ Adhesion Promoter AP596 / 3M™ Primer. 3M™ OEM Polyurethane Glass Adhesive Sealant 590 was used for this test. Note: The following data represents the overlap shear results of a 17 mil bond line. All substrates were abraded and solvent wiped prior to bonding, then cured...

Abrir o catálogo na página 2

3M™ Adhesion Promoter/Primer • Adhesion Promoter AP596 • Fritted Glass Primer P590 • Plastic Primer P591 • Metal Primer P592 • Teak & Glass Primer P595 • Teak & Glass Primer P597, Clear Directions for Use Surface Preparation: Surfaces to be sealed or bonded should be clean and dry. Surfaces should be free from grease, mold release, oil, water/condensation, and other contaminants that may affect the adhesion of the sealant. Abrading with 180 to 220 grit abrasive followed by a solvent wipe will improve the bond strength. Suitable solvents include 3M™ Adhesive Remover, methyl ethyl ketone...

Abrir o catálogo na página 3

3M™ Adhesion Promoter/Primer • Adhesion Promoter AP596 • Fritted Glass Primer P590 • Plastic Primer P591 • Metal Primer P592 • Teak & Glass Primer P595 • Teak & Glass Primer P597, Clear Directions for Use (continued) Apply 3M™ Adhesion Promoter AP596 to both substrates: Pour 3M AP596 Adhesion Promoter onto a soft lint-free cloth folded in quarters. Wipe the bonding area, flipping the cloth at regular intervals to reveal a clean section. With a new clean folded cloth, wipe off the 3M AP596 Adhesion Promoter in the same manner, flipping the cloth at regular intervals to reveal a clean...

Abrir o catálogo na página 4

3M™ Adhesion Promoter/Primer • Adhesion Promoter AP596 • Fritted Glass Primer P590 • Plastic Primer P591 • Metal Primer P592 • Teak & Glass Primer P595 • Teak & Glass Primer P597, Clear Technical Information The technical information, recommendations and other statements contained in this document are based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed. Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a particular...

Abrir o catálogo na página 5