Catalog excerpts
SELF-PRIMING PUMPS FEATURES Body: Impeller: Shaft: Wear Plate: Shaft Seal: Bearings: Ports: Weight: Bronze Neoprene, Nitrile Stainless Steel Replaceable Lip Type Sealed Ball Bearing 1/4" NPT Internal 1-1/2 lb (0.7 kg) approx. Neoprene Impeller Nitrile Impeller APPLICATIONS 3. SPEEDS - 100 RPM to the maximum shown in the performance table. Consult the factory for operation at speeds above those shown. For longer pump life, operate at lowest possible speeds. 4. SELF-PRIMING - Primes at low or high speeds. For vertical dry suction lift of 10 feet, a minimum of 800 RPM is required. Pump will produce suction lift up to 22 feet when wetted. BE SURE SUCTION LINES ARE AIRTIGHT OR PUMP WILL NOT SELF-PRIME. 5. RUNNING DRY - Unit depends on liquid pumped for lubrication. CAU TION Do not run dry for more than 30 seconds. Lack of liquid will damage the impeller. 6. NOTICE - If pumping light fraction petroleum derivatives, solvents, thinners, highly concentrated or organic acids, consult Jabsco Chemical Resistance Table (which is available upon request from ITT Jabsco) for proper body materials and impeller compounds. If corrosives fluids are handled, pump life will be prolonged if pump is flushed with water after each use or after each work day. 7. PRESSURES - Consult Head Capacity Table for recommended maximum for continuous operation. It pressures exceed those shown, consult the factory. 8. TEMPERATURES - Neoprene 45°–180°F (7°–82°C), Nitrile 50°–118°F (10°–82°C). 9. FREEZING WEATHER - Drain unit by loosening end cover. 10. GASKET - Use a standard pump part. Thicker gasket will reduce priming ability. A thinner gasket will cause the impeller to bind. Standard gasket is 0.010" thick. 11. SPARE PARTS - To avoid costly shut downs, keep a JABSCO Service Kit on hand. MARINE: Engine cooling, Pumping bilges, Washdowns, Circulating water in bait tanks. INDUSTRIAL: Circulating and transferring, Velocity-mixing, Pumping machine tool coolants, Return spill, Sump drainage, Chemicals, Pharmaceuticals, Soap, Liquors, Ink, Dyes, Alcohol, Various acids, Tanning liquors, Glycerine, Brine. OPERATING INSTRUCTIONS 1. INSTALLATION - Pump may be mounted in any position. Intake and discharge ports are determined by the direction of shaft rotation (refer to Dimensional Drawing). Before installing, turn the pump shaft in the direction of the operating rotation, 2. DRIVE - Belt or Direct with flexible coupling. BELT DRIVE - Overtight belt load will reduce bearing life. DIRECT DRIVE - Clearance should be left between drive shaft and pump shaft when installing coupling. Always mount and align pump and drive shaft before tightening the coupling set screw. NOTICE: If drive pulley or coupling must be pressed on shaft, remove end cover and impeller and support shaft from impeller end during press operation. Do not hammer a pulley or coupling on shaft. Failure to follow above instructions can damage the pump. TOTAL HEAD 500 RPM P.S.I. Ft.of Water GPM (kg/sq cm) (metre) (LPM) HP NOTE: Progressively longer life may be expected as operating pressures and speeds are reduced. Factory Application Engineering assistance suggested for operation in light shaded area and recommended for heavy shaded area. Capacitor type motor recommended. Table shows approximate Head-Row for new pump in U.S. gallon
Open the catalog to page 1SERVICE INSTRUCTIONS EXPLODED VIEW Impeller Replacement: Remove end cover screws, end cover and gasket.Grasp impeller hub with water pump pliers and pull straight out of body. Lubricate impeller bore.Once started, line up impeller screw with slot in shaft and push impeller straight into body. Lubricate face of impeller, install gasket, end cover, and secure with end cover screws. Major Repair: Follow steps outlined above to remove impeller. Remove outer bearing seal, remove bearing to body retaining ring. Pressing on impeller end of shaft, remove shaft and bearing assembly. Remove inner...
Open the catalog to page 2All Xylem catalogs and brochures
-
23680 Technical Data Sheet
2 Pages
-
23610 Technical Datasheet
2 Pages
-
18670 Technical Datasheet
4 Pages
-
18660 Technical Datasheet
4 Pages
-
18220 Promotional Datasheet
2 Pages
-
General_Industrial_Catalo
24 Pages
-
Jabsco Marine Toilets
16 Pages
-
Oil_Change_Diesel
6 Pages
-
Flexible Impeller Pumps
54 Pages
-
Marine Product Catalog
7 Pages
-
Additional Information 11
4 Pages
-
Chemical Resistance Guide 10
6 Pages
-
Specialty Products 09
6 Pages
-
Sliding Vane Pumps 08
2 Pages
-
Oscillating Pumps 07
2 Pages
-
Rotary Lobe Pumps 06
3 Pages
-
Industrial Pumps Catalogue
94 Pages
-
FLOJET Beverage Run Rise Charts
10 Pages
-
Washdown Pumps
2 Pages
-
Water Pressure Systems
10 Pages
-
Toilet Systems
14 Pages
-
Livewell/Baitwell Pumps
6 Pages
-
Bilge Pumping Systems
24 Pages
-
Aerogen Wind Generator
3 Pages
-
Speciality Products
5 Pages
-
Sliding Vane Pumps
5 Pages
-
Oscillating Pumps
2 Pages
-
Rotary Lobe Pumps
3 Pages
-
Hand Pumps
2 Pages
-
Gear Pumps
2 Pages
-
Diaphragm Pumps
15 Pages
-
Centrifugal Pumps
19 Pages
-
MODEL 34754-0000
2 Pages
-
MODEL 34744-0000
2 Pages
-
4125 SERIES
4 Pages
-
4105 series
4 Pages
-
Exploded View
2 Pages
-
Impeller Replacement
10 Pages
-
Searchlights
8 Pages
-
Ventilation Blowers
4 Pages
-
General Purpose Pumps
8 Pages
-
Oil Change & Diesel
6 Pages
-
Washdown Pumps
2 Pages
-
Water Pressure Systems
10 Pages
-
Livewell/Baitwell Pumps
6 Pages
-
Toilet Systems
12 Pages
Archived catalogs
-
Bilge Pumping Systems
26 Pages
-
Service Parts
80 Pages
-
Impeller Replacement
16 Pages
-
Searchlights
12 Pages
-
Oil Change & Diesel
10 Pages
-
FLOJET BevJet
12 Pages
-
General Purpose Pumps
14 Pages
-
OVERVIEW OF PARTS
2 Pages
-
59000_aqua_filta_promo
2 Pages
-
Type III MSD Waste
18 Pages
-
52600 Series
18 Pages
-
SELF-PRIMING
4 Pages
-
VENTED LOOP SOLENOID
1 Pages
-
233SL Dual Beam Searchlight
2 Pages
-
MINI ACCUMULATOR TANK
2 Pages
-
Par-Max Series
2 Pages
-
Jabsco
2 Pages
-
Marine Product Guide
24 Pages
-
Brochure
4 Pages