XCMG XTF12012K Telescopic Handler

Product catalog summary

Performance
The XCMG XTF12010K telehandler has a maximum lifting capacity of 12,000 kg, a maximum lifting height of 9.8 meters, and a maximum outreach of 5.3 meters. It can lift up to 7,000 kg at maximum height and 3,600 kg at maximum amplitude. The lifting and lowering speeds are 23 and 18 seconds respectively, while the extension and retraction speeds are 17 and 10 seconds.

Driving Capacity
The telehandler has a maximum travel speed of 28 km/h and a gradeability of 28% when overloaded. It features a leveling range of ±10° and a turning radius of 4.6 meters. The transfer mode is hydrostatic, and it offers multiple steering modes including front, crab, and circle.

Main Technical Data
The unladen weight with forks is 18,000 kg. The overall dimensions are 2500 mm in width, 3000 mm in height, and 6330 mm in length. The engine meets Euro 5 emission standards with a displacement of 4.5 L, power of 129 kW at 2200 rpm, and torque of 780 N·m at 1500 rpm. The hydraulic system pressure is 280 bar, with a hydraulic oil tank volume of 290 L and a fuel tank volume of 340 L.

Main Parts List
The telehandler is equipped with a Cummins QSB4.5 engine, Dana-358 transmission, and OMCI axles. The main pump and valve are provided by Parker Hannifin Corporation, and the steering gear is from Jining Eaton Hydraulic System Co., Ltd. Tires are supplied by Double Coin Tyre Group Ltd, and forks by Cascade Fork Co., Ltd.

Notes
This document is for reference only and should not be used for operating the telehandler. The machine is classified as off-road and must comply with local traffic regulations. It should be operated on firm ground with a gradient not exceeding 3% and is only permissible under wind conditions below grade 6. Differences in wind speed between ground and high air, as well as between flat ground and city air, should be considered.

Catalog excerpts

作业性能 Performance 主要技术参数 Main Technical Data 主要配套件明细表 Main parts l

Open the catalog to page 2

作业性能 Performance 举升能力 Lifting Capacity 最大起升高度 Max.lifting height 最大高度吊重量Max.height lifting capacity 最大幅度吊重量Max.amplitude lifting capacity 举升/下降速度 Unladen lifting/lowering speed 外伸/回缩速度 Unladen Extension/retraction speed 属具配置 Attachment Selection 行驶性能 Driving Capacity 调平范围 Leveling range

Open the catalog to page 3

主要技术参数 Main Technical Data 项目 Item 整机重量（含货叉）Unladen weight(with forks) 长度Overall length 离地间隙 Ground clearance 货叉倾翻角度（上倾翻/下倾翻）Tilting angle of fork(tip up/tip down) 液压系统压力 Hydraulic system pressure 液压油箱容积 Hydraulic oil tank volume 燃油箱容积 Fuel tank volume 货叉规格（可选配）Fork specifications(optional)

Open the catalog to page 4

主要配套件明细表 Main parts list 序号 N0. 前桥Front axle 后桥Rear axle 美国德纳 America Dana 意大利 OMCI Italy OMCI 意大利 OMCI Italy OMCI 派克汉尼汾流体传动有限公司 Parker Hannifin Corporation 派克汉尼汾流体传动有限公司 Parker Hannifin Corporation 济宁伊顿液压系统有限公司 Jining eaton hydraulic sy

Open the catalog to page 5

All information in the brochure is provided for reference only. Never rely on it to operate the machine. Refer to the operation manual for operation instructions of the machine. The machine belong to off-road machines. Local traffic rules and regulations must be observed. For long-distance job site transfer, use a trailer and take GVW, axle load and dimensions of the machine into consideration. The machine must be operated on firm ground, which gradient does not exceed 3%. Operation of the machine is permissible only when the wind force is below grade 6. When operating the machine under wind,...

Open the catalog to page 6

XCMG XTF12012K Telescopic Handler

XCMG XTF12012K Telescopic Handler

Catalog excerpts

All XCMG catalogs and brochures