Ideal for any mid to large size vessel with limited access from the interior. • Brightest surface mounted underwater light available today. • Available in single color or RGB color changing • Incorporates a unique silicone optic. A Seavision first. • Latest High Density LED Chip technology (COB Chip) • Reliable 50,000 hour lifespan. • Two year warranty. • Combined with additional back plate allows removal underwater for repair/servicing. • Easy installation. SV60 LED technical specifications Application for: GRP / fiberglass / wood hulls –––––––––––––––––––––––––––––––––––––––––––––– Lamp: COB High intensity LED array –––––––––––––––––––––––––––––––––––––––––––––– Available in: White, Blue or RGB –––––––––––––––––––––––––––––––––––––––––––––– Life length: Approx. 40,000 + hours –––––––––––––––––––––––––––––––––––––––––––––– Kelvin colour temp: 7000 Lumens: 14,630 –––––––––––––––––––––––––––––––––––––––––––––– Glass lens: Borosilicate glass Thickness: 0.19” / 4.8mm Diameter: 3.5” / 88mm –––––––––––––––––––––––––––––––––––––––––––––– Power supply: 100 – 277 VAC 50/60Hz, 1.1 – 0.45 Amp input Max 150W output –––––––––––––––––––––––––––––––––––––––––––––– Casing material: Marine Bronze Dimensions: Diameter: 5.19” / 132mm Depth: 1.43” / 36.4mm ––––––––––––––––––––––––––––––––––

Introduction: Congratulations on the purchase of your new surface mount LED array light (Patent Pending). Underwater Lights® USA, LLC takes pride in providing well designed, high quality and thoroughly tested lights that allow you to “enhance your boating experience”. These lights can be installed in your vessel for aesthetics, to attract fish and/or for security and safety. General Operating Information: The latest commercial grade “COB” High-Density Light Emitting Diode (LED) technology used in this light will provide robust and reliable operation under normal operating conditions when used...

This light should be installed at least 125-150mm (5-6") below the water line by qualified/approved personnel using proper tools and materials. The placement of surface mounted underwater lights on the hull bottom or sides is not recommended. After selecting a flat mounting surface on the vessel hull, drill a 12mm (1/2") diameter hole for Electrical Cable (13) and 6.5mm (1/4") diameter hole for Phillips Oval Head Screw (9). Apply marine grade sealant to back of light then attach using Phillips Oval Head Screws (7 + 9), Large Flat Washer (10) and Hex Locknut (11). Note: Depending upon mounting...

SURFACE MOUNT LED THRU HULL MOUNTING FLANGE Introduction: The optional Thru Hull Mounting Flange is used when “vessel in water” Surface Mount LED Light servicing or replacement will be required. Installation (See Image Below): The Mounting Flange should be installed at least 125-150mm (5-6”) below the water line by qualified/approved personnel using proper tools and materials on a hull thickness of 10mm (0.4”) minimum to 102mm (4”) maximum. Placement of the Mounting Flange on the hull bottom or sides is not recommended. Select a flat hull surface and cut a 19mm (0.75”) diameter hole through the...

SURFACE MOUNT LED THRU HULL MOUNTING FLANGE Introduction: The Thru Hull Mounting Flange is used when “vessel in water” Surface Mount LED Light servicing or replacement will be required. Servicing or Replacement (See Image Below): From inside the vessel, disconnect electrical cable and loosen Cable Strain Relief. From outside the vessel, remove three Phillips Oval Head Fasteners and SV60 Light with Flange Gasket and electrical cable. Note: An optional Blocking Cap with Sealing Disk can be installed inside the vessel to temporarily stop water intrusion. Reverse prior procedure to install new SV60...