*mynauticexpo

SV44 Surface Mount

Product catalog summary

Introduction:
The Sea Vision SV44 is an underwater light featuring a six LED array housed in thermally conductive plastic with a convex lens design. This design enhances light dispersion and magnification, making it suitable for boats requiring surface-mounted applications or those with limited interior access.

Technical Specifications:

Application: Suitable for fiberglass and wood hulls.
Lens: Convex cylindrical glass.
Power Supply: 11-28V DC, 0.81 Amps at 24V, 1.95 Amps at 12V.
Light Source: White or blue LED array with a lifespan of approximately 30,000 hours.
Color Temperature: 6500 Kelvin, 1292 Lumens.
Dimensions: 164mm (6.46”) length, 44mm (1.73”) height, 29mm (1.14”) thickness.
Construction: Black nylon and thermoplastic.
Installation: Fastened with three flat head screws.

General Operating Information:
The LED technology ensures robust operation under normal conditions. The light can be briefly operated out of water and while the vessel is underway. The beam can reach up to 9 meters (30 feet) depending on water clarity.

Safety Information:

Disconnect power before working on the light.
Install on flat surfaces of fiberglass or wood hulls.
Remove marine growth from the lens with a soft brush.

Installation Instructions:
Install at least 125-150mm below the waterline using appropriate tools and materials. Ensure the mounting surface is flat to prevent lens breakage. Use three Phillips Pan Head Screws and marine adhesive for attachment. Avoid electrical wiring and fuel lines during installation.

Troubleshooting and Warranty:
Contact technical support in Florida for assistance. The product comes with a two-year warranty against defects, excluding misuse or improper installation.

Serviceable Parts:
While the LED array and electrical cable are not serviceable, the lens, lens O-ring, glass gasket, and back cover O-ring can be replaced.

Catalog excerpts

Patent Pending SV44 technical specs he Sea Vision SV44 underwater light has a six LED array in a thermally conductive plastic housing that incorporates a revolutionary convex lens. This innovative patent pending design creates greater light dispersion and magnification for a dynamic underwater lighting effect. This light is ideal for any boat wanting a surface mounted application or has interior access problems where thru hull lighting is difficult to install. Application for: Fiberglass / wood hulls ——————————————————————— Glass Lens: Convex cylindrical ——————————————————————— Power Supply: 11-28 volt d.c. - 0.81 Amps 24V/1.95 Amps 12V ——————————————————————— Light Source: White or blue LED array ——————————————————————— Life Length: Approx. 30,000 hours ——————————————————————— Kelvin color temp: 6500 Lumens: 1292 ——————————————————————— Dimensions: Length: 6.46” (164mm) Height: 1.73” (44mm) Thickness: 1.14” (29mm) ——————————————————————— Construction: Black nylon and black thermoplastic ——————————————————————— Installation: Fastened to a at surface by way of three at head screws The placement of surface mounted underwater lights on the hull bottom or sides is not recommended ——————————————————————— Note: All information is subject to change without prior notice, please conrm details prior to ordering. 1881 W. State Road 84, Bay 102, Fort Lauderdale, FL 33315 USA T. 954 760 4447 Toll Free 1 866 772 0130 F. 954 525 3261 [email protected] www.seavision.com

Open the catalog to page 1

SURFACE MOUNTED, LED ARRAY, Congratulations on the purchase of your new surface mounted LED light (Patent Pending). Underwater Lights® USA, LLC takes pride in providing well designed, high quality and thoroughly tested lights that allow you to "enhance your boating experience". These lights can be installed in your vessel for aesthetics, to attract fish, for security and safety. General Operating Information: The commercial grade Light Emitting Diode (LED) technology used in this light will provide robust and reliable operation under normal operating conditions. The light can be operated for...

Open the catalog to page 2

SURFACE MOUNTED, LED ARRAY, 12VDC or 24VDC Installation: This light h ld be installed t least 125-150mm (5 6”) b l Thi li ht should b i t ll d at l t 125 150 (5-6”) below th water li b qualified/approved personnel using proper t l the t line by lifi d/ d l i tools and material. The placement of surface mounted underwater lights on the hull bottom or sides is not recommended. Important! To prevent lense breakage, mounting surface must be flat and have no raised imperfections. To prevent mounting tab breakage, carefully and evenly tighten the three Phillips Pan Head Screws (11) by hand using a...

Open the catalog to page 3