*mynauticexpo

SV42-Thru Hull

Product catalog summary

Introduction:
This document provides technical specifications and installation guidelines for the SV42 LED light designed for boats 40 feet and under. The light is suitable for fiberglass and wood hulls and offers a thru hull installation to avoid exterior wiring.

Technical Specifications:

Application: GRP/fiberglass/wood hulls
Lamp: Six LED modules available in white or blue
Life Length: Approximately 30,000 hours
Color Temperature: 6500 Kelvin
Glass Lens: Convex crown glass
Dimensions: 7.36” x 3.15”
Power Supply: 11-28 VDC, 1.47 amps
Casing Material: Marine Bronze
Weight: 1.4 kg (3 lbs)

Installation Guidelines:
The light should be installed at least 125-150mm below the waterline. The minimum hull thickness is 10mm, and the maximum is 102mm. It is crucial to ensure no electrical wiring or fuel lines are near the installation site. The light must be electrically connected to the vessel's grounding and cathodic protection system.

General Operating Information:
The LED technology provides reliable operation, with a light beam reaching up to 9 meters depending on water clarity. Regular inspection and cleaning of the light and cabling are recommended every six months.

Safety Information:

Do not install or remove the light while the vessel is in the water.
Disconnect power before working on the light.
Ensure proper grounding to prevent corrosion.

Troubleshooting and Warranty:
For technical support, contact the Florida office. The light comes with a two-year warranty against defects in workmanship and materials. Misuse or unauthorized modifications void the warranty.

Serviceable Parts:
While the LED array and electrical cable are not field serviceable, other components like the strain relief O-ring and glass gasket can be replaced as needed.

Catalog excerpts

his light has an LED array in a bronze housing designed for boats 40’ and under that want LED lighting. This light is excellent for any boat which has limited interior access but desires a thru hull installation avoiding any exterior wiring. SV42 technical specifications Application for: GRP / fiberglass / wood hulls ——————————————————————— Lamp: Six LED modules Available in white or blue ——————————————————————— Life length: approx. 30,000 hours ——————————————————————— Kelvin color temp: 6500 ——————————————————————— Glass lens: Convex crown glass ——————————————————————— Thickness: 0.93” / 23.5mm x 2.2" / 57mm ——————————————————————— Power supply: 11-28 VDC - 1.47 amps ——————————————————————— Casing material: Marine Bronze Dimensions: 7.36” / 187mm x 3.15” / 80mm ——————————————————————— Weight: 1.4 kg / 3 lbs ——————————————————————— Code: SV42 – Thru hull ——————————————————————— Total shipping weight: 1.8 kg / 4 lbs ——————————————————————— Installation: recommended at least 5-6” (125-150mm) below waterline between 3-6 feet (1-2 meters) apart. The placement of surface mounted underwater lights on the hull bottom or sides is not recommended ——————————————————————— All information is subject to change without prior notice, please confirm details prior to ordering. 1881 W. State Road 84, Bay 102, Fort Lauderdale, FL 33315 USA T. 954 760 4447 Toll Free 1 866 772 0130 F. 954 525 3261 [email protected] www.seavision.com

Open the catalog to page 1

THRU HULL, LED ARRAY, 12VDC or 24VDC Introduction: Congratulations on the purchase of your new thru hull LED light (Patent Pending). Underwater Lights® USA, LLC takes pride in providing well designed, high quality and thoroughly tested lights that allow you to “enhance your boating experience”. These lights can be installed in your vessel for aesthetics, to attract fish, for security and safety. General Operating Information: The commercial grade Light Emitting Diode (LED) technology used in this light will provide robust and reliable operation under normal operating conditions. Depending upon...

Open the catalog to page 2

THRU HULL, LED ARRAY, 12VDC or 24VDC Installation: This light should be installed at least 125-150mm (5-6”) below the water line by qualified/approved personnel using proper tools and materials. The minimum hull thickness is 10mm (0.4”) and maximum is 102mm (4”). After selecting a flat surface, cut a 19mm (0.75”) diameter hole through the vessel hull in the desired location. Caution! Check that no electrical wiring, fuel lines, oil lines, water lines etc., pass near or through the intended hole location. The placement of surface mounted underwater lights on the hull bottom or sides is not recommended....

Open the catalog to page 3