he Sea Vision SV37 LED weld in model for aluminum or steel hulls can be installed in the transom or the hull, it utilizes high density LED chip technology. The lights can be welded at adjustable angles to suit all hull shapes. The hull shape and positioning will dictate the angle of the light you require, angles available are 0 to 50 degree. The 98mm / 3.8” aperture lens gives the largest volume of light available in a welded fixture. This light was specifically designed to include an intricate cofferdam that is welded to the thru hull providing a very easy way for the shipyard to satisfy the demands of the classification societies for secondary containment of the lights. This fixture is primarily for larger yachts. SV37 LED technical specifications Application for: Aluminum or Steel hulls –––––––––––––––––––––––––––––––––––––––––––––– Light source: High density LED array –––––––––––––––––––––––––––––––––––––––––––––– Life length: approx. 15,000 hours plus –––––––––––––––––––––––––––––––––––––––––––––– Lumens: 8560 –––––––––––––––––––––––––––––––––––––––––––––– Kelvin colour temp: 5600 –––––––––––––––––––––––––––––––––––––––––––––– Glass lens: Borosilicate glass –––––––––––––––––––––––––––––––––––––––––––––– Thickness: 12.7mm / 0.5” –––––––––––––––––––––––––––––––––––––––––––––– Power supply: 90 – 295 VAC 50/60Hz 1.1 – 0.45 amps –––––––––––––––––––––––––––––––––––––––––––––– Casing material: Aluminum 5086 or Stainless Steel 316L –––––––––––––––––––––––––––––––––––––––––––––– Angles available: Flush 30 degree 38 degree 50 degree ——————————————————————— Only required between the light and driver (maximum distance 16 feet / 5 meters). Marine grade electrical cable 18/2 stranded copper wire. Normal ships cable can be used from the ballast to the power supply. ——————————————————————— Code: SV37 LED ——————————————————————— Installation: Recommended at least 10” (250mm) below the waterline between 3 – 8 feet (1 – 2.5 meters) apart. Cable: This is a guideline only, for specic requirements please contact us. All information is subject to change without prior notice, please conrm details prior to ordering. 1881 W State Road 84, Bay 102, Fort Lauderdale, FL 33315 USA T. 954 760 4447 Toll Free 1 866 772 0130 F. 954 525 3261 [email protected] www.seavision.com

Introduction: Congratulations on th purchase of your new weld-in LED li ht f STEEL/ALUMINUM h ll d vessels. U d C t l ti the h f ld i light for hulled l Underwater Li ht ® USA t Lights USA, LLC takes pride in providing well designed, high quality and thoroughly tested lights that allow you to “enhance your boating experience”. These lights can be installed in your vessel for aesthetics, to attract fish, for security and safety. General Operating Information: The commercial grade Light Emitting Diode (LED) technology used in this light will provide robust and reliable operation under normal operating...

Installation: This light should be installed at minimum 250-300mm (10-12”) below the light load water line by qualified/approved personnel 250 300mm (10 12 ) using proper tools, welding procedures and materials. An adequate access area should be left behind the light for servicing and general ventilation. After selecting a location, cut an appropriate sized hole through the vessel hull. Note: Hole size will be defined by the specific weldin Front Flange (17) that came with the light. Caution! Check that no electrical wiring, fuel lines, oil lines, water lines etc., pass near or through the intended...