SV20
3Pages

Catalog excerpts

he Sea Vision SV 20 model is our standard xenon light consoles, cruisers and performance boats. The vessel must with a 35 watt HID xenon lamp and 12 or 24 volt ballast. be hauled out for installation although lamp change and any This light is suitable for small boats wanting to utilize 12 or maintenance can be done in the water from within the hull. 24 volt DC power and can be installed on sport fishers, center SV20 technical specifications Application for: GRP/fiberglass/wood hulls ——————————————————————— Lamp: 35 watt HID xenon ——————————————————————— Life length: approx. 3,000 hours plus ——————————————————————— Lumens: 3,600 ——————————————————————— Kelvin colour temp: 5100 ——————————————————————— Glass lens: Borosilicate glass ——————————————————————— Thickness: 9.5mm / 0.38” ——————————————————————— Power supply: 12 VDC start up current max. 18 amps, 3.5 amps continuous 24 VDC start up current max. 8 amps, 1.8 amps continuous ——————————————————————— Casing material: Marine Bronze Dimensions: 80 mm (3.15”) x 128mm (5.04”) ——————————————————————— Angles available: Flush ——————————————————————— Weight: 2.2Kg/5.9lbs ——————————————————————— Code: SV20 ——————————————————————— Ballast: 12 VDC / 24 VDC attached with a 425mm/17” cable. This cable cannot be spliced into. ——————————————————————— Dimensions: Length: 89mm/3.5” Width: 125mm/4.92” Depth: 42.5mm/1.67” ——————————————————————— Total shipping weight: 1.9 Kg / 5 lbs ——————————————————————— Installation: Recommended at minimum 6” (152 mm) below waterline between 3 - 6 feet (1 - 2 meters) apart. (60mm) 2.36” cut out hole ——————————————————————— Optional lamp: 35 watt HID xenon with 10000 Kelvin color temperature ——————————————————————— Note: Please specify voltage when ordering. All information is subject to change without prior notice, please confirm details prior to ordering. USCG Ignition Protected 1881 W State Road 84, Bay 102, Fort Lauderdale, FL 33315 USA T. 954 760 4447 Toll Free 1 866 772 0130 F. 954 525 3261 sales@seavision.com www.seavision.com

Open the catalog to page 1

Introduction: Congratulations on the purchase of your new thru hull light. Underwater Lights® USA, LLC takes pride in providing well designed, high quality and thoroughly tested lights that allow you to “enhance your boating experience”. These lights can be installed in your vessel for aesthetics, to attract fish, for security and safety. General Operating Information: The 35W, HID, gas discharge lamp used in this light is a commercial grade high technology instant re-strike lamp. This lamp will generally reach full brightness in less than 1 minute. The light can be operated for a brief...

Open the catalog to page 2

Installation: This light should be installed at least 152mm (6”) below the water line by qualified/approved personnel using proper tools and materials. The minimum hull thickness is 8mm (0.31”) and maximum is 73mm (2.87”) with an access area of at least 75mm (3”) left behind the light for lamp servicing and general ventilation. After selecting a flat surface, cut a 60mm (2-3/8”) diameter hole through the vessel hull in the desired location. Caution! Check that no electrical wiring, fuel lines, oil lines, water lines etc., pass near or through the intended hole location. Remove numbers (7),...

Open the catalog to page 3