SV14 HID
7Pages

Catalog excerpts

steel weld in underwater light he Sea Vision SV14 weld in model for steel hulls can be installed in the transom or the hull, it utilizes a 150 watt HID metal halide lamp and 110-230 volt AC power. The lights can be welded at adjustable angles to suit all hull shapes. The hull shape and positioning will dictate the angle of the light you require, angles available are 0 to 50 degree. The vessel must be hauled out for installation although lamp change and any maintenance can be done in the water from within the hull. The light body is designed to act as a cofferdam / secondary containment for additional security. SV 14 (Steel) 24 degree mount shown. Application for: Steel hulls –––––––––––––––––––––––––––––––––––––––––––––– Lamp: 150 watt HID metal halide –––––––––––––––––––––––––––––––––––––––––––––– Life length: approx. 3,000 hours plus –––––––––––––––––––––––––––––––––––––––––––––– Lumens: 12,000 –––––––––––––––––––––––––––––––––––––––––––––– Kelvin colour temp: 7500 –––––––––––––––––––––––––––––––––––––––––––––– Glass lens: Borosilicate glass Thickness: 12.7mm / 0.5" " –––––––––––––––––––––––––––––––––––––––––––––– Power supply: 120 VAC 50/60Hz input - running current 1.33 amps 230 VAC 50/60Hz input - running current 0.59 amps –––––––––––––––––––––––––––––––––––––––––––––– Casing material: Stainless steel 316 L Dimensions: Flush - Diameter: 100mm / 4” Length: 175 mm / 7” 10-24 degree - Diameter: 100mm / 4” Length: 175 mm / 7” 24-38 degree - Diameter: 140mm / 5.5” Length: 175mm / 7” 38-50 degree - Diameter: 140mm / 5.5” Length: 175mm / 7” –––––––––––––––––––––––––––––––––––––––––––––– Angles available: Flush - weight 3.7 kg/8.2 lbs code: SV14 SS ﬂush 10-24 degree - weight 4.5 Kg / 9.9 lbs code: SV14 SS 24 deg 24-38 degree - weight 9.6 Kg / 21.1 lbs code: SV14 SS 38 deg 38-50 degree - weight 10.2 Kg / 22.5 lbs code: SV14 SS 50 deg ––––––––––––––––––––––––––––––––––––––––––––––

Open the catalog to page 1

Introduction: Congratulations on the purchase of your new weld-in light for STEEL hulled vessels. Underwater Lights® USA, LLC takes pride in providing well designed, high quality and thoroughly tested lights that allow you to “enhance your boating experience”. These lights can be installed in your vessel for aesthetics, to attract fish, for security and safety. General Operating Information: The 150W, HID, gas discharge lamp used in this light is not an instant re-strike lamp. This means that it must be allowed to cool for approximately 10 to 20 minutes after being shut off before being...

Open the catalog to page 2

This light should be installed at minimum 250-300mm (10-12") below the light load water line by qualified/approved personnel using proper tools, welding procedures and materials. An access area of at least 75mm (3") should be left behind the light for lamp servicing and general ventilation. After selecting a location, cut an appropriate sized hole through the vessel hull. Note: Hole size will be defined by the specific weld-in Front Flange (18) that came with the light. Caution! Check that no electrical wiring, fuel lines, oil lines, water lines etc., pass near or through the intended hole...

Open the catalog to page 3

Weld-in Front Flange Selection for STEEL Hulled Vessels Light with 0° to 10° SS Front Flange (14020) Light with 10° to 24° SS Front Flange (14025) Underwater Lights USA, LLC 1881 W State Road 84, Bay 102 Fort Lauderdale, FL 33315 USA Phone: 1-954-760-4447 Fax: 1-954-525-3261 Internet: www.seavision.com Email: sales@seavision.com DOC:071405-16 Underwater Lights Europe Sarl 16, rue Rouaze 06400 Cannes, France Phone: 33-(0)-4-97-21-02-96 Fax: 33-(0)-4-97-21-10-96 Internet: www.seavision.com Email: sales@seavisioneurope.com

Open the catalog to page 4