SV10-250W
3Pages

Catalog excerpts

he Sea Vision SV 10 model offers the largest aperture of all the fiberglass models giving maximum light output from the 250 watt HID metal halide lamp. It can be installed in the transom or the hull and is suitable for boats with 110-230 volt AC power, including sportfish, yachts and cruisers. The vessel must be hauled out for installation although lamp change and any maintenance can be done in the water from within the hull. Application for: GRP/fiberglass/wood hulls ——————————————————————— Lamp: 250 watt HID metal halide ——————————————————————— Life length: approx. 3,000 hours plus ——————————————————————— Lumens: 17,000 ——————————————————————— Kelvin colour temp: 8000 ——————————————————————— Glass lens: Borosilicate glass ——————————————————————— Thickness: 12.7mm / 0.5” ——————————————————————— Power supply: 120 VAC 50/60Hz input running current 2.38 amps 230 VAC 50/60Hz input running current 1.15 amps ——————————————————————— Casing material: Marine Bronze / Marine Aluminum Dimensions: 130 mm (5.12”) x 203 mm (8.0”) ——————————————————————— Angles available: Flush ——————————————————————— Weight: 3.5 Kgs /8 lbs ——————————————————————— Code: SV10/250W ——————————————————————— SV34 100-277 VAC 250W 60/50 Hz ——————————————————————— Weight: 6.5 Kg / 14 lbs ——————————————————————— Cable: Only required between the light and ballast Maximum distance from 15 feet / 4.5 meters to 33 feet / 10 meters (depending on ballast model) High temperature silicone, 18/3 shielded copper wire. Normal ships cable can be used from the ballast to the power supply. ——————————————————————— Total shipping weight: 9.52 Kg/21 lbs ——————————————————————— Installation: Recommended at minimum 10" (250mm) below light load waterline between 3-8 feet (1-2.5 meters) apart. (100mm) 4” cut out hole This is a guideline only, for specific requirements please contact us. ——————————————————————— All information is subject to change without prior notice, please confirm details prior to ordering. 1881 W State Road 84, Bay 102, Fort Lauderdale, FL 33315 USA T. 954 760 4447 Toll Free 1 866 772 0130 F. 954 525 3261 sales@seavision.com www.seavision.com

Open the catalog to page 1

Introduction: BY UNDERWATER LIGHTS USA Congratulations on the purchase of your new thru hull light (Patent Pending). Underwater Lights® USA, LLC takes pride in providing well designed, high quality and thoroughly tested lights that allow you to "enhance your boating experience". These lights can be installed in your vessel for aesthetics, to attract fish, for security and safety. General Operating Information: The 250W, HID, gas discharge lamp used in this light is not an instant re-strike lamp. This means that it must be allowed to cool for approximately 10 to 20 minutes after being shut...

Open the catalog to page 2

Installation: To be installed by qualified personnel only at minimum 250-300mm (10-12”) below the light load water line using proper tools and materials. The yq p y ( ) g gp p minimum hull thickness is 10mm (0.4”) and maximum (for sufficient light cooling) is 50mm (2.0”) with an access area of at least 75mm (3”) left behind the light for lamp servicing and general ventilation. After selecting a flat surface, cut a 100mm (4”) diameter hole through the vessel hull in the desired location. Caution! Check that no electrical wiring, fuel lines, oil lines, water lines etc., pass near or through...

Open the catalog to page 3