*mynauticexpo

SV10-150W

Product catalog summary

Introduction: The Sea Vision SV 10 model is a high-performance underwater light designed for fiberglass, wood, and GRP hulls. It features a 150-watt HID metal halide lamp, providing a maximum light output of 12,000 lumens with a color temperature of 7500 Kelvin. The light is suitable for boats with 110-230 volt AC power and can be installed in the transom or hull.

Technical Specifications: The SV10 light has a borosilicate glass lens with a thickness of 12.7mm. It operates on 120 VAC with a running current of 1.33 amps or 230 VAC with a running current of 0.59 amps. The casing is made from marine bronze or marine aluminum, and the light weighs 3.5 kg. The ballast, model SV18, weighs 1.9 kg, and the total shipping weight is 5.3 kg.

Installation: Installation requires the vessel to be hauled out. The light should be installed at a minimum of 250-300mm below the waterline, with a hull thickness between 10mm and 90mm. A 100mm diameter hole is needed for installation, and care must be taken to avoid existing wiring and lines.

Operating Information: The HID lamp requires a cooling period of 10-20 minutes after being shut off before restarting. It reaches full brightness in approximately 2 minutes and should be left on for at least 10 minutes to prevent flickering. The light can be operated while the vessel is underway, and the beam can reach up to 30 meters depending on water clarity.

Safety Information: The light must be electrically connected to the vessel's grounding and cathodic protection system to prevent corrosion. High-temperature silicone cable is required between the light and ballast. Regular inspections every six months are recommended for the light, cabling, and ballast box.

Maintenance: Lamp replacement involves removing six nuts and the projector lid, then replacing the lamp in the socket. Glass replacement follows a similar procedure, ensuring all surfaces are clean before reassembly.

Warranty: The product is warranted against defects in workmanship and materials for two years, excluding lamps. Misuse, improper installation, and unauthorized modifications void the warranty.

Contact Information: For technical support, contact Underwater Lights USA, LLC in Fort Lauderdale, FL, or Underwater Lights Europe Sarl in Antibes, France. Detailed contact information is provided for both locations.

Catalog excerpts

he Sea Vision SV 10 model offers the largest aperture of all the fiberglass models giving maximum light output from the 150 watt HID metal halide lamp. It can be installed in the transom or the hull and is suitable for boats with 110-230 volt AC power, includ- Patent Pending ing sportfish, yachts and cruisers. The vessel must be hauled out for installation although lamp change and any maintenance can be done in the water from within the hull. Application for: GRP/fiberglass/wood hulls ——————————————————————— Lamp: 150 watt HID metal halide ——————————————————————— Life length: approx. 3,000 hours plus ——————————————————————— Lumens: 12,000 ——————————————————————— Kelvin colour temp: 7500 ——————————————————————— Glass lens: Borosilicate glass ——————————————————————— Thickness: 12.7mm / 0.5” ——————————————————————— Power supply: 120 VAC 50/60Hz input running current 1.33 amps 230 VAC 50/60Hz input running current 0.59 amps ——————————————————————— Casing material: Marine Bronze / Marine Aluminum Dimensions: 130 mm (5.12”) x 203 mm (8.0”) ——————————————————————— Angles available: Flush ——————————————————————— Weight: 3.5 Kgs /8 lbs ——————————————————————— Code: SV10 ——————————————————————— SV18 120 VAC 50/60Hz 230 VAC 50/60 Hz ——————————————————————— Weight: 1.9 Kg / 5 lbs ——————————————————————— Cable: Only required between the light and ballast (maximum distance 50 feet / 15 meters). High temperature silicone, 18/3 shielded copper wire. Normal ships cable can be used from the ballast to the power supply. ——————————————————————— Total shipping weight: 5.3 Kg/14 lbs ——————————————————————— Installation: Recommended at minimum 10" (250mm) below light load waterline between 3 - 8 feet (1-2.5 meters) apart. (100mm) 4” cut out hole This is a guideline only, for specific requirements please contact us. ——————————————————————— Note: Please specify voltage when ordering. All information is subject to change without prior notice, please confirm details prior to ordering. USCG Ignition Protected 1881 W State Road 84, Bay 102, Fort Lauderdale, FL 33315 USA T. 954 760 4447 Toll Free 1 866 772 0130 F. 954 525 3261 [email protected] www.seavision.com

Open the catalog to page 1

Congratulations on the purchase of your new thru hull light (Patent Pending). Underwater Lights® USA, LLC takes pride in providing well designed, high quality and thoroughly tested lights that allow you to "enhance your boating experience". These lights can be installed in your vessel for aesthetics, to attract fish, for security and safety. General Operating Information: The 150W, HID, gas discharge lamp used in this light is not an instant re-strike lamp. This means that it must be allowed to cool for approximately 10 to 20 minutes after being shut off before being restarted. HID lamps generally...

Open the catalog to page 2

Installation: To be installed by qualified personnel only at minimum 250-300mm (10-12”) below the light load water line using proper tools and materials. The minimum hull thickness is 10mm (0.4”) and maximum (for sufficient light cooling) is 90mm (3.5”) with an access area of at least 75mm (3”) left behind the light for lamp servicing and general ventilation. After selecting a flat surface, cut a 100mm (4”) diameter hole through the vessel hull in the desired location. Caution! Check that no electrical wiring, fuel lines, oil lines, water lines etc., pass near or through the intended hole location....

Open the catalog to page 3