Catalogs >
Underwater Lights Limited >
UL Ti MATE 75 - Fixed

UL Ti MATE 75 - Fixed
6Pages

Catalog excerpts

underwater lights limited Manufacturer of the original underwater lights Brand marine lighting products since 1991. 30 degree and 50 degree inserts for angled hull adjustment. servicing and upgrades without the hassle of hauling your boat. *We recommend that the installation of the light be a minimum 250mm below the waterline when the yacht is loaded with 50% fuel and 50% water and that the light be angled 15 degrees downwards. *The UL Ti MATE 75 Fixed is recommended for Steel and Aluminium hull yachts of apart for the best illumination. *With complete Lloyd’s Register Approval, GL and ABS Design Appraisal on all components, the UL Ti MATE 75 has been installed on some of the largest and most prestigious Superyachts in the world. Weld-in Insert Light Projector Installation Installation 5083 Aluminium Weld-in 316L Stainless Steel Weld-in SpecSheet_UL75Fixed150_010115v1 Installation Angles Flush+: White Flush+: White Technical Lumens Typical Bulb Life Expectancy Min-Max Operating Voltage Ballast Type Ballast Output Control Options Physical Length of fixture Part Number 30 Degree Profile (height) of fixture Removal Space Required Total weight Cable Length Hole Cut-out 5083 Aluminium / 316L Stainless Steel Borosilicate Glass 12mm for flush+ & 20mm for 30 & 50 Degree Borosilicate Glass Part Number Flush + Beam Angle 1.5m up to 5m ( Port & Starboard sides) Control Options *Distance between lights can vary from 1.5 (transom) to 5 meters (port & starboard) Aluminium & Steel Boat size Hull Material Your Local Dealer © 2015 Underwater Lights Limited All Rights Reserved. Underwater lights limited reserves the right to change specifications without notice. Part Number 50 Degree Max Hull plate thickness The Great Dunton Forge, London Road Dunton Green, Sevenoaks, Kent TN13 2TD UK T: +44 (0) 1732 455753 • F: +44 (0) 1732 743233 E: uwl@underwaterlights.com www.underwaterlights.com VAT NO: 556 4425 31

Open the catalog to page 1

Open the catalog to page 2

UL Ti MATE 75 316L STAINLESS STEEL AND 5083 ALUMINIUM ORDERING NUMBERS FLUSH - S00300-75-ICE. 30 DEG - S00330-75-ICE. 50 DEG -S00350-75-ICE FLUSH - S00600-75. 30 DEG - S00630-75. 50 DEG -S00650-75 WITH 120 (Y3) / 230 (V2) VOLT BALLAST AND 150W (W2) WATT LAMP. OPERATIONAL CONDITIONS AND CONSIDERATIONS The UL Ti MATE 75 is serviced from inside the hull. Allow ♦ Do not attempt to remove the glass lens while afloat. access for maintenance and space for ventilation. Do not use the LIGHT in dry-dock or out of the water Allow a minimum of 70mm behind the projector lid (item 2) for lamp...

Open the catalog to page 3

Ballast voltage 120/230 volts, wattage 150 watts. Cable length between ballast and projector should be kept to a minimum. The ballast has the capability to operate the lamp with a cable length of 10 meters . Cable specification -3 core braided silicone rubber 210 degrees C Spark Test 10kV Lamp cable preparation - It is extremely important that the cable insulation is not damaged or broken as shown in the picture (right). The ballast could fail should the ignition voltage of 5000 volts short across from the lamp cable to the earth.. Shorting across the high voltage cable will stop the lamp...

Open the catalog to page 4

DESIGN, INSTALLATION AND OPERATION OF THE UL Ti MATE 75 SA underwater lights limited™ XQGHUZDWHU OLJKWV OLPLWHG Manufacturers of the Original underwater lights Brand Marine Lighting Products since 1991 BASIC CRITERIA All weld-ins must have a minimum depth of 250-300mm below a waterline based on a loading of 50% fuel and 50% freshwater. They can be used to a maximum depth of 150 metres. Spacing of the weld-ins: stern - 1.5 to 2.5 metres: port or starboard - 2.0 to 6.0 metres. Angle of the weld-in light beam to the waterline: 15-20 degree. There are three different angled weld-ins available...

Open the catalog to page 5

underwater lights limited™ Manufacturers of the Original I II 11 lerwxa! er ligl its Brand Marine Lighting Products since 1991 THE UL Ti MATE 75 SA INSTALLATION (Steel and aluminium hulls) The UL Ti MATE 75 SA welding procedures shown are typical for most installations and are for guidance purposes only. Always use a certified welder and a fire watch when welding. Protect all threads against welding, grinding and painting. Welding procedure Ref.No: Joint type: Preparation & cleaning: Parent material spec: Material thickness (mm): Outside diameter (mm): Filler metal classification: Filler...

Open the catalog to page 6