Trelleborg MArI N e AND INFRASTRUCTURE RE SmartMoor Series II SmartMoor Series II Quick Release Hooks Quick Release Hook (QRH) units are available with single or multiple hooks in capacities from 30t to 200t. Each hook cantilevers from the mounting base and the design ensures the hook cannot impact the deck under any loading configuration. The QRH is designed to be released by an operator when a mooring line is attached, even under full load. Field proven since 1972 and installed in over 600 mooring facilities worldwide, Trelleborg’s quick release hooks are the foundation for today’s modern mooring systems. Certified Management System Trelleborg Marine Systems’ commitment to continuous product improvement means that we reserve the right to upgrade and modify equipment and systems without notice as technological and operational parameters dema

SmartMoor Series II Models Single Hook Double Hook Triple Hook Quadruple Hook

CP45 (Safe Working Load = 45 tonnes) Cp60 (Safe Working load = 60 tonnes) CP75 (Safe Working load = 75 tonnes) CP100 (Safe Working load = 100 tonnes) CP125 (Safe Working load = 125 tonnes) CP150R (Safe Working Load = 150 tonnes) CP200 (Safe Working Load = 200 tonnes) Dimensions available upon request Note 1: Dimensions are in mm. Note 2: Dimensions are typical. Always request a certified hook/base drawing before starting construction. Note 3: customised bases to suit bolt patterns are available upon request. Note 4: Shipping Mass includes base, capstan, hold down bolts and packing. Mass is for...

1 QRH GENERAL SPECIFICATIONS - STANDARD MODELS (For variances to standard product refer to options and Upgrades) 1.2 Base Capacity Standard Hook Base Foundation Design Requirements Hold Down Bolts (anchors) Hook SwL multiplied by the number of hooks. E.g. double hook of 75 tonne SwL = 150 tonne; triple hook = 225 tonne Spheroidal graphite cast iron, ASTM A536 65-45- 12 equivalent to 400-12 to AS1831 (standard cast hook base). operating: -15°c to +60°c Storage: -40°c to +70°c (-40°F to 158°F) (Models with a lower minimum temperature are available. consult our engineers) Designed in accordance...

Frame (side plates): Carbon Steel ASTM A572 Grade 50 equivalent to AS 3678 Grade 350, . 1.10 Hook construction Hook body, main pivot block, primary release block: cross shaft are high strength alloy steel to ASTM A148, equivalent to AS 2074. Vertical Pin: high tensile alloy steel grade SAE4140. Loadcells + dummy pins ASTM A276 431 equivalent to AS 2837 431. The hook assembly is fitted with three elastomeric impact blocks for energy absorption. Material: polypropelene. One line per hook is recommended for hooks with Load Monitoring ASTM E1444-05 All hooks are individually load tested using NATA...

Capstan - Specifications The Trelleborg Marine Systems electric capstan motor is housed within a protective structure (typically the QRH base). The capstan motor is factory run-in and mated with a gearbox, which is oil-filled for life. The capstan motor Direct on Line (DoL) motor starter allows the operator to control motor operation through a footswitch, Emergency Stop Switch (E-Stop) and direction selector switch. Ribbed capstan head and rope guide are fitted as standard. Hazardous and safe area models are available. 1 CAPSTAN GENERAL SPECIFICATIONS - STANDARD MODELS (For variances to standard...

1 CAPSTAN GENERAL SPECIFICATIONS - STANDARD MODELS (For variances to standard product refer to options and Upgrades) Capstan Type Line Speed Environmental Protection (minimum) Brake Details Reversible, with brake Nominal 30 metres/minute capstan motor and motor starter: IP56 minimum Footswitch: IP68 Note: Motor contains tropic-proofed windings Automatic, spring applied brake when de-energised Holding torque = 150% of motor torque. Mounting requirements See QRH base details Fasteners where possible all fasteners used in the assembly of the support structure are 316 stainless steel. 2 capstan motor...