TRANBERG HIGH VOLTAGE SOLUTIONS

TRANBERG was established in 1901 and is located in Stavanger, the “oil capital” on the west coast of Norway. Due to the oil industry, oil companies and offshore vessel ship owners have found their base in Stavanger. This has made it possible for Tranberg to develop and test products in close cooperation with our customers. Since the start, Tranberg has designed, manufactured and supplied high quality electromechanical products for use on ships and offshore installations. Equipment capable of performing under all climatic conditions, from arctic cold to tropical heat, is a special feature for...

High Voltage Enclosure systems Tranberg has delivered Medium and High voltage connecting systems for use in hazardous areas for several large projects. We have specialized knowledge for manufacturing approved enclosure systems for Topside Umbilical Termination Units, to assemble complex Umbilical cables consisting of High voltage, Signals and Fibre optical cables. These solutions are also used at refinery installations and Non-Ex areas. Our knowledge and experience for these solutions has resulted to develop Medium Voltage Enclosure also for minor cable diameters, i.e. 2,5 - 35mm2. These are...

TEF 1060 A-BLOCK SYSTEM ZONE 1, ZONE 2 & SAFE AREA Tranberg A-Block solution with use of Phoenix ExTerminals, are developed according to IEC60079. The solution is standardized up to 11kV, and is certified by notified body according to ATEX and IECEx. The assembling with Ex-terminals is a compact and vibration stabile solution. The A-Block solution can be used with current load up to 100Amps. The solution is very flexible and Tranberg can customize the A-Block system for maximum 35mm2 with ferrules, up to 11kV. Compact solution Flexible design Up to 100A Up to 11kV CU bar for earthing Bottom side...

Ambient temperature: Enclosure material: Finish: Ingress Protection: Safety cover: Earthing: Bonding: Cable glands: -20° to +40°C with standard EPDM gasket, -50° to +60°C with silicone gasket, other ambient temperatures on request. AISI 316L / EN 1.4404 Bright chemical dip IP 66 IP 20 Internal copper bar or PE terminals Through studs on enclosure Tranberg Ex cable glands as standard Classification: For use in Hazardous areas Zone 1 or 2, or in safe area. Atex-Certificate: Presafe 14 ATEX 4124 IECEx Certificate: IECEx PRE 14.0001 Marking Atex: Ex II 2 G Ex d e IIC Gb/Ex II 2 G Ex eb IIC/ Ex II...

The CU Bus-Bar System system is developed and standardized up to 11kV, and is certified by notified body according to ATEX and IECEx. The High Voltage solution with tinned copper bus-bars combined with the use of Ex-certified Isolators. 3 different types of bus-bar solutions. • Type-R is with Rectangular bus-bar • Type-C is with rectangular bus-bar assembled in a Curved frame system • Type-G is with G-profile bus-bar Atex-Certificate: Presafe 14 ATEX 4124 IECEx Certificate: IECEx PRE 14.0001 Atex: Ex II 2 G Ex d e IIC Gb/Ex II 2 G Ex eb IIC/ Ex II 2 G Ex e mb IIC Gb IECEx: Ex d e IIC Gb/Ex eb...

Designed for one cable in and one cable out each phase A cost effective solution Designed for max 300mm2 Max load 432A Available with certified cable cleats To withstand Short-circuit for even 50kA Technical data • Standardized for bottom side entries • All CU connection Bars are tinned • All products delivered with Tranberg cable glands • Bright chemical dip surface threated • Material: AISI316L Optional • Lifting lugs, Certified to Standard 2.7.1 • Short circuit devices • Tranberg Enclosure Heater with thermostat • Cable Cleats • Optical Fiber Termination • Padlock facility • Exi Safety switch •...

TOPSIDE UMBILICAL TERMINATION UNITS ZONE 1, ZONE 2 & SAFE AREA Single core contact system cabinet with Enclosure Heater and Optical Fiber Termination Solution for multi-contact termination Single core contact system

Single core contact system in a combined MV/LV/FO solution. The LV/FO compartment is welded in the MV compartment to simplify dismantling and installation of the umbilical. Outlets and service from the outside provides easy access to the LV/FO compartment. • High voltage enclosures up to 36kV • Signal cable junction boxes • Fibre cable junction boxes • Complete and customized solutions • Light weight • Cost effective installation • Short delivery times • Zone 1 Exe max 11kV • Zone 2 Ex nR above 11 kV • Exd or Exp for use in Zone 1 above 11 kV Type of protection • Zone 1 Exe max 11kV • Zone 2...

l 26 to 150mm in 12 sizes for single / parallel formation l Operating temperature -50°C to +60°C CABLE CLEATS l Low Smoke & Fume (LSF) liners as standard l Combined single (M12) and two bolt (M10) fixing design Sapphire (SHDSS cable cleat) Features l Third party certification to IEC 61914:2009 l 316L stainless steel The CMP Products SHDSS cable cleat range consists of metallic cable cleats which have been designed, constructed, and tested in accordance with the International Standard ‘cable cleats for Electrical w w w.c m p - p ro d u c t s .co m Installations’ IEC 61914:2009. The SHDSS cable...

TECHNICAL DATA & CLASSIFICATION CABLECLEAT SELECTIONTABLE

Project Kuff Gas Ceiba C3 & C4 Ceiba C3 & C4 Ekofisk Growth Columba E Maersk Brenda Gas power Qatar Gas Seawater pump Ceiba C5 Tordis Azurite North Belut North Belut Jacky-Beatrice Njord-A Gudrun Shelly Customer ABB Power System Framo Engineering Framo Engineering Scanrope Subsea Cables Framo Engineering ABB Denmark Framo Engineering Statoil Karsto Scanrope Subsea Cables Talisman Energy Framo Engineering Framo Engineering Framo Engineering R.Stahl Far East JDR Cable UK Duco Cable UK Aibel Aibel Framo Engineering Johan Sverdrup Field Centre Phase 1 EPma - FLARE TIP & IGNITION PACKAGE. HV-JB A-Block...