Modular Instrument System SMIS Multi-Function Gauges Engine Interface Cable and Power Cables 4” Multi-Function Gauge The 4” Multi-Function Gauge uses a state-of-theart high-contrast, dot matrix display to monitor real-time graphic and numerical digital data. When connected into the SMIS system, it can monitor all engine functions, Speedometer, Tachometer, GPS* and many others. 990C0-88164-KIT 4” multi-function gauge kit includes: Suzuki Modular Instrument System (SMIS) uses an easy to connect and expandable cable system to transmit graphic and numerical data to MultiFunction gauges. This easy to set up and install system can be used with nearly any boat and DF9.9B thru DF300 Suzuki Outboard. Connected to the NMEA 2000® compatible system, the gauges can display real-time readings from compatible electronic probes and the exclusive SMIS engine interface to monitor all engine functions. (Engine Monitor with 4” gauge only). 4” Multi-Function Gauge Female Terminator Male Terminator NMEA “T” Power Cable Interface Cable 4” Multi-Function Gauge (Gauge Only) Engine Interface Cable SMIS Adapters (not shown) Special Adaptor must be used with SMIS Engine Interface to connect the DF150G/175G/ 200AP/250AP/300AP Outboard to the system. NMEA Adaptor Harness (not shown) Allows connection to other NMEA devices (Device NET). 990C0-88137 NMEA Device to Blue “T” 990C0-88029 Blue Device to NMEA “T” Connection Hardware T-Connector 990C0-88154-KIT 2” multi-function gauge kit includes: 2” Multi-Function Gauge Female Terminator Male Terminator NMEA “T” Power Cable Interface Cable 25’ Backbone Cable SMIS Adaptor 990C0-88150 2” Multi-Function Gauge (Gauge Only) Single Engine Adapter T-Connectors link all compatible cable, data and sensor devices and can be easily secured. Dual Engine Adapter Triple Engine Adapter The 2” Multi-Function Gauge is capable of all functions of the 4” gauge except Engine Monitoring Functions. When connected to the SMIS system, it a can be programmed to monitor all other functions. Dual Engine Tachometer Display The most important part of the SMIS data system. DF9.9B thru DF300 Suzuki Outboards can connect to the system using the exclusive SMIS Engine Interface. (Adaptor Cable also needed for DF150G/175G/200AP/250AP/300AP applications.) Required in order to put new style 990C0-88149 Interface cable on older system with blue connector. *GPS requires additional hardware. Suzuki Modular Instrument System Engine Interface Cable (not shown) Quad Engine Adapter Terminating Resistors SMIS Adaptor – to connect at engine SDS connector 120 ohm Terminating Resistors are required for any open cable ends in the system. Connection Cable (not shown) 990C0-88113 Terminator – Female 990C0-88114 Terminator – Male The Extension Cable is the mainline of the Suzuki Modular Instrument System. Data communication runs the length of the boat, capped at each end with a 120 ohm Terminating Resistor. NMEA 2000 compatible sensors or other devices can be added by the use of T-Connectors throughout the system. Monitors fluid levels such as fuel, live well water level, etc. 10ft cable. 990C0-88116 Fluid Level Sensor SMIS Power Cable (not shown) Sensors Fluid Level Sensor (not shown) Speed Sensor (not shown) Paddle wheel-type speed sensor. 10ft cable. 990C0-88117 Speed Wheel Temperature Sensor (not shown) Surface Water Temperature sensor. 10ft cable. Temperature Sensor Quad Power Node (not shown) Temperature Sensor – Thru Hull Pressure Sensor (not shown) GPS receiver module interface for display of accurate location and speed on Multi-Function Gauges. Fused(3A) lead connects extension cable to the power source. Allows network to be powered from multiple power sources (key switch, accessory switch, etc…). Trim Gauge Display Single Power Cable Quad Power Node Fuel Gauge Display 990C0-88120 GPS Module Optional Instrument Trims Change the standard black bezel to suit your application. 4 different bezel finishes to choose from for 2” or 4” Multi-Function gauges. 990C0-88113 Terminating Register – Female 990C0-88021-6PK Chrome Bezel 4” (not shown) 990C0-88023-6PK White Bezel 4” (not shown) 990C0-88025-6PK Chrome Bezel 2” 990C0-88027-6PK White Bezel 2” 990C0-88114 Terminating Register – Male 990C0-88025-6PK Chrome Bezel 2” 990C0-88136 Adapter Interface to SDS Port on Engine