PRODUCT DATA SHEET PHENGUARD™ 930 DESCRIPTION Two-component, high-build, amine adduct-cured novolac phenolic epoxy holding primer PRINCIPAL CHARACTERISTICS • Primer coat in the PHENGUARD tank coating system • Excellent resistance to a wide range of organic acids, alcohols, edible oils, fats (regardless of free fatty acid content) and solvents • Maximum cargo flexibility • Low cargo absorption • Good resistance to hot water • Recognized corrosion control coating (Lloyd's register) • Good application properties, resulting in a smooth surface COLOR AND GLOSS LEVEL • Offwhite • Eggshell BASIC DATA AT 20°C (68°F) Data for mixed product Number of components Mass density Volume solids Directive 1999/13/EC, SED: max. 191.0 g/kg max. 315.0 g/l (approx. 2.6 lb/US gal) Recommended dry film thickness Theoretical spreading rate Overcoating Interval Minimum: 36 hours Maximum: 21 days Full cure after Shelf life Base: at least 12 months when stored cool and dry Hardener: at least 12 months when stored cool and dry Notes: - See ADDITIONAL DATA – Spreading rate and film thickness - See ADDITIONAL DATA – Overcoating intervals - See ADDITIONAL DATA – Cu

PRODUCT DATA SHEET PHENGUARD™ 930 RECOMMENDED SUBSTRATE CONDITIONS AND TEMPERATURES Substrate conditions • Steel should be blast cleaned in situ to at least ISO-Sa2½ • Blasting profile 50 – 100 µm (2.0 – 4.0 mils) • Steel must be free from rust, scale, shop primer and any other contamination • The substrate must be perfectly dry before and during application of PHENGUARD 930 Substrate temperature and application conditions • Substrate temperature during application and curing should be above 10°C (50°F) • Substrate temperature during application and curing should be at least 3°C (5°F) above dew...

PRODUCT DATA SHEET PHENGUARD™ 930 Air spray Recommended thinner THINNER 91-92 Volume of thinner 0 - 10%, depending on required thickness and application conditions Nozzle orifice 2.0 mm (approx. 0.079 in) Nozzle pressure 0.3 MPa (approx. 3 Bar; 44 p.s.i.) Airless spray Recommended thinner THINNER 91-92 Volume of thinner 0 - 10%, depending on required thickness and application conditions Nozzle orifice Approx. 0.46 – 0.53 mm (0.018 – 0.021 in) Nozzle pressure 15.0 MPa (approx. 150 bar; 2176 p.s.i.) Brush/roller • Brush: for stripe coating and spot repair only Recommended thinner THINNER 91-92...

PRODUCT DATA SHEET PHENGUARD™ 930 ADDITIONAL DATA Spreading rate and film thickness DFT Theoretical spreading rate Note: Maximum DFT when brushing: 60 µm (2.4 mils) Overcoating interval for DFT up to 100 µm (4.0 mils) Overcoating with... Note: Surface should be dry and free from any contamination Curing time for DFT up to 150 µm (6.0 mils) Substrate temperature Minimum curing time before transport of cargoes without note 4, 7, 8 or 11 and ballast water or tank test with sea water Notes: - Minimum curing time of PHENGUARD tank coating system before transport of cargoes with note 4, 7, 8 or 11:...

PRODUCT DATA SHEET PHENGUARD™ 930 SAFETY PRECAUTIONS • For paint and recommended thinners see INFORMATION SHEETS 1430, 1431 and relevant Material Safety Data Sheets • This is a solvent-borne paint and care should be taken to avoid inhalation of spray mist or vapor, as well as contact between the wet paint and exposed skin or eyes • This product contains a substance that is the subject of a TSCA 5a Significant New Use Rule (SNUR) [to be published] WORLDWIDE AVAILABILITY It is always the aim of PPG Protective and Marine Coatings to supply the same product on a worldwide basis. However, slight modification...