Catalogs >
Sigma Coatings PPG PMC >
AMERCOAT 114 A

AMERCOAT 114 A
1 / 5Pages

Catalog excerpts

PRODUCT DATA SHEET AMERCOAT® 114 A (Formerly Nu-Klad 114A; Also branded as Megasel CF) DESCRIPTION Epoxy filler compound PRINCIPAL CHARACTERISTICS • Suitable for use on primed steel or direct to concrete/masonry • Pit filler / seam sealer for steel • Filler for bug holes and surface cracks in concrete • Suitable as a masonry block filler / scratch coat • Excellent chemical resistance COLOR AND GLOSS LEVEL • Offwhite BASIC DATA AT 68°F (20°C) Data for mixed product Number of components Volume solids Theoretical spreading rate Shelf life Base: at least 36 months when stored cool and dry Hardener: at least 36 months when stored cool and dry Flush with surrounding substrate to fill voids See ADDITIONAL DATA – Overcoating intervals See ADDITIONAL DATA – Curing time 1.33 gallons in a 20-lb kit RECOMMENDED SUBSTRATE CONDITIONS AND TEMPERATURES Steel • Abrasive blast to SSPC SP-10 standards. Prepare surface in accordance with application instructions for the specific primer being used.

Open the catalog to page 1

PRODUCT DATA SHEET AMERCOAT® 114 A (Formerly Nu-Klad 114A; Also branded as Megasel CF) Concrete • Cure concrete a minimum of 14 days and until 80 percent of its physical properties have been attained before applying this product • Prepared surfaces according to ASTM D4258 (surface cleaning) and either ASTM D4259 (abrading), or ASTM D4260 (acid etching) • Blow / vacuum cracks and bugholes free of loose particulates Concrete block • Walls must be laid plumb and square with flush joints. Do not rake joints • All surfaces must be clean and dry as per ASTM D4261 Substrate temperature • Surface...

Open the catalog to page 2

PRODUCT DATA SHEET AMERCOAT® 114 A (Formerly Nu-Klad 114A; Also branded as Megasel CF) Application • Amercoat 114A can be applied via short nap roller, trowel, putty knives, squeegee, or a combination of these methods. Spread 114A across the surface applying uniform pressure to achive a smooth finish. Leave only a slight film above the surface plane. • A rounded trowel can be used to form a cove based of up to 1 inch. • Amercoat 114A may be used to fill surface voids up to 1" in width or depth. • Amercoat 114A is not elastomeric and will not bridge dynamic cracks. • Area should be sheltered...

Open the catalog to page 3

PRODUCT DATA SHEET AMERCOAT® 114 A (Formerly Nu-Klad 114A; Also branded as Megasel CF) Curing time for DFT up to 5.0 mils (125 µm ) Substrate temperature Note: Drying times are dependent on air and steel temperature, applied film thickness, ventilation and other environmental conditions Pot life (at application viscosity): AMERCOAT 68 A Mixed product temperature Product Qualifications • Compliant with USDA Incidental Food Contact Requirements • NFPA Class A for Flame Spread and Smoke Development • Nuclear Service Level 2 (partial) SAFETY PRECAUTIONS • For paint and recommended thinners see...

Open the catalog to page 4

PRODUCT DATA SHEET AMERCOAT® 114 A (Formerly Nu-Klad 114A; Also branded as Megasel CF) WARRANTY PPG warrants (i) its title to the product, (ii) that the quality of the product conforms to PPG’s specifications for such product in effect at the time of manufacture and (iii) that the product shall be delivered free of the rightful claim of any third person for infringement of any U.S. patent covering the product. THESE ARE THE ONLY WARRANTIES THAT PPG MAKES AND ALL OTHER EXPRESS OR IMPLIED WARRANTIES, UNDER STATUTE OR ARISING OTHERWISE IN LAW, FROM A COURSE OF DEALING OR USAGE OF TRADE,...

Open the catalog to page 5

AMERCOAT 114 A 1 / 5Pages

Catalog excerpts

All Sigma Coatings PPG PMC catalogs and brochures

AMERCOAT 114 A
1 / 5Pages