RCS® Remote Control Systems
1 / 64Pages

RCS® Remote Control Systems Push/Pull Cables • Control Levers • Pedals • Pull Only Cables Edition 2022/2023 RINGSPANN® Registered Trademark of RINGSPANN GmbH, Bad Homburg RCS® Registered Trademark of RINGSPANN RCS GmbH, Obe

RCS® Remote Control Systems Control lever systems Push/Pull cables Setup and description of push/pull cables Overview of push/pull cables Basic cable series Selection of cable sizes Connection type T of cable end parts Accessories for control lever 58.x Connection type G of cable end parts Accessories for friction control 22.x Connection type R or S of cable end parts Codes of practice and health and safety regulations Order key for push/pull cables for control lever systems Assembly information Order key for push/pull cables Throttle pedal systems Introduction to throttle pedal systems...

Setup and description of push/pull cables Setup A flat wire-reinforced inner member is located in a conduit, which is formed by an inner-lying inner tube and specially arranged longitudinal wires (linear wire stranding). The linear wires on the other hand (with the exception of types 770) are supported and fixed by a support wire winding. A plastic extrusion is doing the outer coverage of the conduit. For the universal connection of elements, the inner member and conduit are supported with pressed on zinccoated or stainless steel end parts. The push/pull cables are designed lightly gliding...

Overview of push/pull cables Cable series Bend radius Temperature range Sliding characteristics extra light

Cable sizes • Travel up to 76 mm • Push forces 70 N • Pull forces 450 N • Travel up to 152 mm • Push forces 135 N • Pull forces 540 N • Travel up to 152 mm • Push forces 225 N • Pull forces 1 035 N * upon request • Travel up to 152 mm • Push forces 450 N • Pull forces 1 800 N • Travel up to 152 mm • Push forces 1 35

Cable series the basis of Remote Control System Our cable series are offered in five sizes. In the standard version, three end part configurations are designed. There are six different types of tra- vel, which can be combined with three different seals. A multitude of additional possibilities for configuration and variation in the setup of the cables are possible in order to create a solution that fits to the respective application. Series 383 and 384 • Series 383 with zinc-coated end parts and stainless steel rod ends • Series 384 with stainless steel end parts • PTFE-covered inner member...

Series 275 and 274 • Series 275 with zinc-coated end parts and stainless steel rod ends • Series 274 with stainless steel end parts • Inner member stainless steel reinforced • Highly efficient • Remarkably small bend radii • Extremely smooth • High travel frequencies • Colour: blue • For cable sizes U, V, L and M • High temperature range from -50 °C to +90 °C (constant) and short term up to +110 °C 7-1 Series 775 and 774 • Series 775 with zinc-coated end parts and stainless steel rod ends • Series 774 with stainless steel end parts • Attractive pricing • Highly efficient • For applications...

Selection of cable sizes Cable sizes, maximum travel, bend radii, seals, thread rod ends, outer diameter of conduits and push and pull forces depending on the travel Cable sizes, maximum travel, bend radii, seals, thread rod ends and outer diameter of conduit Cable size Bend radius for cable series Outer diameter of conduit for cable series 383/384 Push and pull forces depending on the travel The specified forces are applicable for use in permanent operation with a long service life. A safety factor of 1.5 can be used to calculate the temporary overloads. Pull forces diagram 4 000 Push...

Selection of cable sizes Efficiencies Efficiencies The efficiency of a push/pull cable (the relation of the required cable operating force to a given output force) is particularly influenced by the number of bends laid in the cable. The cable operating force can be calculated in accordance with the following formula: Operating force = Output force x Efficiency factor α is the sum of all cable bends in degrees. In addition to the cable bends, the cable length is to be taken into consideration with 15° for every 1 meter. Example of efficiency factor Cable series Cable size Cable length Sum of...

Standard end parts Connection types of cable end parts, wiper seals and lubrication Connection types of cable end parts Rigid screw endfitting type S and R Swiveled bulkhead endfitting type T Swiveled clamp endfitting type G Wiper seals Seal no. 05 The rubber wiper seal has been proven for all cable sizes for normal applications in the entire machine construction. Upon request also with a support tube from stainless steel. Automatic self-adjusting PTFE wiper seal in case of wear for cable sizes U, V and L. Protects well against fine dust. Design like seal no. 10 with additional double...

Connections of cable end parts Connection type T Swiveled bulkhead endfitting Cable size Dimensions A Cable size Push/pull cables* at travel of Cable with hand operation** NL/TL (1)/MA TL (2) 51 76 38 mm mm mm * Rod end in mid position ** Rod end completely moved out (see from page 22), TL (1) = variant 1, TL (2) = variant 2 (see page 25) *** Rod end in mid position (see from page 32) Can also be supplied with end parts made of stainless steel.

Connections of cable end parts Connection type G Swiveled clamp endfitting Cable size Dimensions A Cable size Push/pull cables* at travel of 25 mm Cable with hand operation** NL/TL (1)/MA TL (2) 51 76 38 mm mm mm Cables for operating level*** Can also be supplied with end parts made from stainless steel. * Rod end in mid position ** Rod end completely moved out (see from page 22), TL (1) = variant 1, TL (2) = variant 2 (see page 25) *** Rod end in mid position (see from page 32)

Connections of cable end parts Connection type R or S Rigid screw type endfitting Cable size Dimensions A Cable size Push/pull cables* at travel of Cable with hand operation** NL/TL (1)/MA TL (2) 25 51 76 38 mm mm mm mm Cables for operating level*** 16RFA7.2 mm * Rod end in mid position ** Rod end completely moved out (see from page 22), TL (1) = variant 1, TL (2) = variant 2 (see page 25) *** Rod end in mid position (see from page 32) **** only for hand operation TL and MA, not available for NL Dimensions D for cable size and travel: Cable size Dimensions E for cable size L and travel:...