SEAGUARD® 3000 MARINE POLYURETHANE Protective & Marine Coatings SERIES HARDENER PRODUCT DESCRIPTION RECOMMENDED USES SEAGUARD 3000 MARINE POLYURETHANE is a heavy duty, two component, exterior/interior, low VOC, high solids, polyesteraliphatic urethane coating. Provides a high gloss, excellent chemical resistance, color retention, and chalk resistance. • For marine and offshore use where a heavy duty polyurethane coating is required • Resists splash, spillage, and fumes of dilute acids, alkalies, solvents, and fuels • Exterior decks (helipads) • Deck House • Freeboard and topside • Machinery and equipment • Outstanding resistance to a wide range of chemical, weather, and mechanical conditions • Abrasion and impact resistant • Superior exterior color and gloss retention. PRODUCT CHARACTERISTICS PERFORMANCE CHARACTERISTICS Wide range of colors available Volume Solids: 70% ± 2%, mixed, may vary by color Weight Solids: 80% ± 2%, mixed, may vary by color Unreduced: <250 g/L; 2.1 lb/gal Reduced 10%: <340 g/L; 2.8 lb/gal Recommended Spreading Rate per coat: Wet mils (microns) Dry mils (microns) ~Coverage sq ft/gal (m2/L) Theoretical coverage sq ft/gal 1120 27.4 (m2/L) @ 1 mil / 25 microns dft NOTE: Brush or roll application may require multiple coats to achieve maximum lm thickness and uniformity of appearance. Test Name Abrasion Resistance Accelerated Weathering - QUV (Primer) To touch: 16 hours To handle: 24 hours To recoat: minimum: 24 hours maximum: 3 days To cure: 7 days 2 hours 30 minutes 20 minutes 5 hours 2 hours 1.25 hours Pot Life: 5 hours Sweat-in-Time: Shelf Life: Flash Point: Reducer/Clean Up: 2 hours 1 hour None required Passes, >70% Gloss retention Adhesion, steel Direct Impact Resistance Exterior Durability Flexibility Humidity Resistance 2 hours 1.25 hours 24 hours 18 hours 5 days 48 hours If maximum recoat time is exceeded, abrade surface before recoating. Drying time is temperature, humidity, and lm thickness dependent. 63 mg loss (average of 5 trials) Pencil Hardness 12 hours 48 hours 7 days ASTM D3359 Method B; ASTM D4541 Drying Schedule @ 4.0 mils wet (100 microns): @ 50°F/10°C Test Method ASTM D4060, CS17 wheel, 1000 cycles, 1 kg load ASTM D4587, QUV-A, 3000 hours Salt Fog Resistance, with primer Part A - 36 months, unopened Part B - 12 months, unopened Store indoors at 40°F (4.5°C) to 100°F (38°C). 102°F (39°C) TCC, mixed Reducer # R6K30 www.sherwin-williams.com/protective 200°F (93°C), 250°F (121°C) intermittent Excellent, 87% gloss retention Passes No blistering, cracking, softening or delamination H Rating 10 per ASTM D610 for rusting, less than 1/16" creepage at scribe. No blistering, cracking, softening, or delamination of the lm.

SEAGUARD® 3000 MARINE POLYURETHANE Protective & Marine Coatings SERIES HARDENER PRODUCT INFORMATION SURFACE PREPARATION RECOMMENDED SYSTEMS Dry Film Thickness / ct. Mils (Microns) Steel: 1-2 cts. SeaGuard 5000 HS 1-2 cts. SeaGuard 3000 Marine Polyurethane or 1-2 cts SeaGuard 6000 1-2 cts SeaGuard 3000 Marine Polyurethane Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion. Refer to product Application Bulletin for detailed surface preparation information. Minimum recommended surface preparation:...

SEAGUARD® 3000 MARINE POLYURETHANE Protective & Marine Coatings SERIES HARDENER APPLICATION BULLETIN APPLICATION CONDITIONS SURFACE PREPARATIONS Temperature: 40°F (4.5°C) minimum, 120°F (49°C) maximum (air, surface, and material) At least 5°F (2.8°C) above dew point Iron & Steel Remove all oil and grease from surface by Solvent Cleaning per SSPC-SP1. Minimum surface preparation is Commercial Blast Cleaning per SSPC-SP6/NACE 3. For better performance, use Near White Metal Blast Cleaning per SSPC-SP10/NACE 2. Blast clean all surfaces using a sharp, angular abrasive for optimum surface prole (1-2...

SEAGUARD® 3000 MARINE POLYURETHANE Protective & Marine Coatings SERIES HARDENER APPLICATION BULLETIN APPLICATION PROCEDURES PERFORMANCE TIPS Surface preparation must be completed as indicated. Mixing Instructions: Mix paint thoroughly to a uniform consistency with low speed power agitation prior to use. Make certain no pigment remains on the bottom of the can. Then combine two parts by volume of Part A with one part by volume of Part B. Thoroughly agitate the mixture with power agitation. Allow the material to sweatin as indicated. Re-stir before using. Stripe coat all crevices, welds, and sharp...