MIL-DTL-24441/19C TYPE III Protective & Marine Coatings F159 EPOXY POLYAMIDE ZINC RICH PRIMER PART A PART B N10A359 N10V359 GRAY/GREEN BINDER Revised 9/11 9.42 PRODUCT DESCRIPTION RECOMMENDED USES MIL-DTL-24441/19C Type III F159 is a two component, low VOC, epoxy polyamide zinc rich primer. This product offers excellent cathodic protection as well as adhesion, water resistance, and chemical resistance. For use over aluminum and steel substrates to provide chemical and corrosion resistance. PRODUCT CHARACTERISTICS PERFORMANCE CHARACTERISTICS Finish: Flat Color: Gray Green, Formula 159 Volume Solids: 64.6% ± 2%, mixed Weight Solids: 84.9% ± 2%, mixed VOC (EPA Method 24): Unreduced: • Complies with MIL-DTL-24441, F159, Type III. • Complies with Military Specication MIL-DTL-24441, F159, Type III. • For use where SCAQMD Rule 102 air pollution regulations for solvent in marine coatings apply. <340 g/L; 2.80 lb/gal Color Zinc Primer Gray/Green 159, Part A Zinc Primer, Part B Product/Rex Number N10A359 N10V359 Zinc Content in Dry Film: 85% by weight Mix Ratio: 2 components, premeasured 1:4 by volume, 2.5 gallon mix Recommended Spreading Rate per coat: Wet mils (microns) Dry mils (microns) ~Coverage sq ft/gal (m2/L) Minimum 5.0 (125) 3.0 (75) 250 (6.1) Maximum 6.0 (150) 4.0 (100) 336 (8.2) Theoretical coverage sq ft/gal 1034 (25.3) (m2/L) @ 1 mil / 25 microns dft NOTE: Brush or roll application may require multiple coats to achieve maximum lm thickness and uniformity of appearance. Drying Schedule @ 5.0 mils wet (125 microns): 35-40°F 41-60°F (1.6-4.5°C) (4.5-16°C) Dry to touch: To recoat: minimum: maximum: Cure to service: Pot Life: Sweat-in-Time: 12 hours 8 hours 61-80°F (16-27°C) 50% RH 81-100°F (27-38°C) 6 hours 4 hours 24 hours 18 hours 12 hours 8 hours 14 days 12 days 10 days 7 days 6 days 5 days 4 days 64 hours 4 hours at 77°F/25°C, 50% RH @ 35-60°F (1.6-16°C): 2 hours @ 61-70°F (16-21°C): 1-1.5 hours @ 71-90°F (21-32°C): 30 minutes - 1 hour @ 90°F+ (32°C+): none Shelf Life: Flash Point: Reducer/Clean Up: 36 months, unopened Store indoors at 40°F (4.5°C) to 100°F (38°C) 100°F (38°C), PMCC, mixed Hi-Flash Naphtha, R2K5 www.sherwin-williams.com/protective continued on back

MIL-DTL-24441/19C TYPE III Protective & Marine Coatings F159 EPOXY POLYAMIDE ZINC RICH PRIMER PART A PART B N10A359 N10V359 GRAY/GREEN BINDER PRODUCT INFORMATION SURFACE PREPARATION RECOMMENDED SYSTEMS Dry Film Thickness / ct. Mils (Microns) Steel: 1 ct. MIL-DTL-24441/19C Type III F159 Primer 2 cts. MIL-DTL-24441, Type III Epoxy Steel: 1 ct. MIL-DTL-24441/19C Type III F159 Primer 2 cts. MIL-DTL-24441, Type IV Epoxy 9.42 3.0-4.0 (75-100) 3.0-4.0 (75-100) 3.0-4.0 (75-100) 4.0-6.0 (100-150) Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other...

MIL-DTL-24441/19C TYPE III Protective & Marine Coatings F159 EPOXY POLYAMIDE ZINC RICH PRIMER PART A PART B N10A359 N10V359 APPLICATION BULLETIN APPLICATION PROCEDURES GRAY/GREEN BINDER 9.42 PERFORMANCE TIPS Surface preparation must be completed as indicated. Mix contents of Part B thoroughly with low speed power agitation. Make certain no pigment remains on the bottom of the can. Then combine one part by volume of Part A with four parts by volume of Part B. Thoroughly agitate the mixture with power agitation. After mixing, pour through a 60 mesh screen. Allow the material to sweatin as indicated...