Protective & Marine Coatings EURONAVY ES301S HIGH EDGE RETENTION SOLVENT-FREE EPOXY EDGE RETENTIVE VERSION PART A: PART B: N02MIL-S SERIES N02CA301S Revised 12/10 9.60 PRODUCT DESCRIPTION RECOMMENDED USES EURONAVY ES301S is a solvent-free, surface and humidity tolerant two-pack modied epoxy. It can be applied without dew point restrictions. ES301S provides chemical and abrasion resistance and very good edge-retentive properties. It can be applied over steel prepared by hydroblasting, grit blasting or mechanical tooling. · Superior impact resistance · Non-ammable · Good chemical resistance · No dew point or relative humidity restrictions · Excellent anticorrosive properties · Can be applied on vessels while on the water EURONAVY ES301S is an anticorrosive coating for long service life steel protection, normally used as an intermediate or topcoat as part of a ES301 based coating system when very high edge retentive is required (assuring high lm thickness over welds and at sharp edges). It can be used for both immersion and above waterline service in marine, offshore, construction and industrial applications. PRODUCT CHARACTERISTICS It is suitable for new building, conversion, repair or maintenance applications. It provides superior performance protecting areas such as ballast tanks, void tanks, crude oil tanks, slop tanks, mud pits, wet spaces, bilges, decks, external hull and steel bridges. Suitable for use in USDA Inspected Facilities. Color: Red Oxide, Light Gray, White, Dark Gray Finish: Semi-gloss Volume Solids: 97% ± 3% Weight Solids: 98% ± 2% PERFORMANCE CHARACTERISTICS Test Name After 1,000 hrs salt fog VOC (EPA Method 24): <150 g/L Mix Ratio: 4:1, by volume Theoretical Spreading Rate per coat: Wet mils (microns) Dry mils (microns) ~Coverage sq ft/gal (m2/L) Minimum 4.0 (100) 4.0 (100) 267 (6.7) Drying Schedule @ 4.0 mils wet (100 microns): @ 40°F/4.4°C @ 59°F/15°C @ 77°F/25°C @ 104°F/40°C 50% RH To touch: 24 hours 16 hours 6 hours 2 hours To recoat: minimum 48 hours 24 hours 16 hours 6 hours maximum 16 days 10 days 7 days 4 days To cure: 15 days 10 days 4 days 36 hours Pot Life 3 hours 60 minutes 35 minutes 10 minutes Drying time is temperature, humidity, and lm thickness dependent. Flash Point: Clean Up: After 700 hrs salt Adhesion (pull-off) fog Maximum 6.0 (150) 6.0 (150) 401 (10) Theoretical coverage sq ft/gal 1604 (39.3) (m2/L) @ 1 mil / 25 microns dft NOTE: Brush or roll application may require multiple coats to achieve maximum lm thickness and uniformity of appearance. Shelf Life: Test Method 12 months, unopened Store indoors at 40°F (4.5°C) to 100°F (38°C) >212°F (>102°C), mixed (ASTM D56) R6K10 (MEK) or R7K104 After 1,000 hrs condensation Atmospheric Exposure 2.5 years Cathodic Disbonding MIL-P-24647, 90 days Edge-retention MIL-PRF-23236 Fire Resistance Humidity Resistance Salt Fog Resistance ASTM E84-01 ASTM D4585, 1,000 hours ASTM B117, 1,000 hours www.sherwin-williams.com/protective Results 1,350 - 1,550 psi (9,3 - 10,8 MPa) (ES301K+ES301S) 1,450 psi (10,0 MPa) (ES301L + ES301S + PU14) NF EN 24624 1,670 - 2,000 psi (11,5 - 13,8 MPa) (ES301K + ES301S) Rust rating: 10 Blistering rating: 10 Scribe undercut: .5mm Passes Ratio of 74 - 101%, for edge radius from 0.1 mm to 2.4 mm, respectively. ES301K + ES301S system Rating A ASTM D1654, Rating: 10 D1654: Rating: 10 continued on back

Protective & Marine Coatings EURONAVY ES301S HIGH EDGE RETENTION SOLVENT-FREE EPOXY EDGE RETENTIVE VERSION PART A: PART B: N02MIL-S SERIES N02CA301S PRODUCT INFORMATION 9.60 SURFACE PREPARATION RECOMMENDED SYSTEMS Dry Film Thickness / ct. Mils (Microns) Immersion or Atmospheric 1-2 cts. EURONAVY ES301L or K 4-6 1 ct. EURONAVY ES301S (optional) 4-6 (100-150) (100-150) The systems listed above are representative of the product's use, other systems may be appropriate. CERTIFICATES AND APPROVALS IMO PSPC: Type Approved as part of a coating system compliant with IMO MSC.215(82) (Performance Standard...

Protective & Marine Coatings EURONAVY ES301S HIGH EDGE RETENTION SOLVENT-FREE EPOXY EDGE RETENTIVE VERSION PART A: PART B: N02MIL-S SERIES N02CA301S APPLICATION BULLETIN APPLICATION PROCEDURES 9.60 PERFORMANCE TIPS Surface preparation must be completed as indicated. Stripe coat all crevices, welds, and sharp angles to prevent early failure in these areas. Mixing Instructions: Mix paint thoroughly to a uniform consistency When using spray application, use a 50% overlap with each pass with low speed power agitation prior to use. of the gun to avoid holidays, bare areas, and pinholes. If necessary,...