EURONAVY ES301L / ES301K
4Pages

Protective & Marine Coatings EURONAVY ES301L / ES301K MOISTURE TOLERANT SOLVENT-FREE EPOXY STANDARD VERSION LOWER TEMP VERSION PART A: PART B: PART A: PART B: N02MIL-K SERIES N02CA301K N02MIL-L SERIES N02CA301L Revised 5/11 9.59 PRODUCT DESCRIPTION RECOMMENDED USES EURONAVY ES301L/K is a solvent-free, surface and humidity tolerant two-pack modied epoxy. It can be applied without dew point restrictions and over damp steel surfaces. ES301L/K show good chemical and abrasion resistance and good edge-retentive properties. It can be applied over steel prepared by hydroblasting, grit blasting or mechanical tooling. · Excellent edge retention (when used with ES301S) · No dew point or relative humidity restrictions · Excellent anticorrosive properties · Can be applied over damp substrates · Can be applied over medium ash rust · Excellent substrate and intercoat adhesion EURONAVY ES301L/K is an anticorrosive coating for long service life steel protection. It can be used for both immersion and above the waterline service in marine, offshore, construction and industrial applications. PRODUCT CHARACTERISTICS It is suitable for new building, conversion, repair or maintenance applications. It provides superior performance protecting areas such as ballast tanks, void tanks, crude oil tanks, slop tanks, mud pits, wet spaces, bilges, decks, external hull and steel bridges. Suitable for use in USDA Inspected Facilities. PERFORMANCE CHARACTERISTICS Test Name Finish: Color: Red Oxide, Moss Green, Light Gray, White, Dark Gray Volume Solids: 97 ± 3% Weight Solids: 98 ± 2% VOC (EPA Method 24): 4:1, by volume Results 1740 - 3480 psi 12,0 - 24,0 MPa 1350 - 1550 psi 9,3 - 10,8 MPa (ES301K+ES301S) 1450 psi / 10,0 MPa (ES301L + ES301S + PU14) NF EN 24624 1670 - 2000 psi 11,5 - 13,8 MPa (ES301K + ES301S) Rust rating: 10 Blistering rating: 10 Scribe undercut: .5mm Passes No defects ~ 15,000 psi (1.050 KgF/cm2) <150 g/L; 1.25 lb/gl Mix Ratio: Test Method After application and curing Semi-gloss After 1000 hrs salt fog Adhesion (Pull-off) ASTM D4541 After 700 hrs salt fog After 1000 hrs condensation Theoretical Spreading Rate per coat: Wet mils (microns) Dry mils (microns) ~Coverage sq ft/gal (m2/L) Minimum 4.0 (100) 4.0 (100) 267 (6.7) NOTE: Brush or roll application may require multiple coats to achieve maximum lm thickness and uniformity of appearance. Atmospheric Exposure 2.5 years Cathodic Disbonding Combined Weathering MIL-P-24647, 90 days NACE TM0184, 4000 hrs. Compressive Strength ISO 844 Corrosion Weathering Maximum 6.0 (150) 6.0 (150) 401 (10) NORSOK M-501 Rev.4, 4200 hrs. ASTM D5894, 4032 hrs. ISO 20340, 4200 hrs. Drying Schedule @ 4.0 mils wet (100 microns): Version: 301L @ 50°F/10°C @ 77°F/25°C 50% RH To touch: Foot trafc: To recoat: minimum: maximum: To cure: Pot life: Version: 301K 48 hours 56 hours 10 hours 24 hours 48 hours 15 days 10 days 4 hours 16 hours 7 days 4 days 45 minutes @ 59°F/15°C @ 77°F/25°C Edge-retention @ 104°F/40°C 50% RH To touch: Foot trafc: To recoat: minimum: maximum: To cure: Pot life: 24 hours 56 hours 14 hours 24 hours 5 hours 16 hours 24 hours 15 days 10 days 8 hours 16 hours 8 days 4 days 3 hours 8 hours 5 days 36 hours 30 minutes MIL-PRF-23236 Elasticity Modulus ISO/R 527 Fire Resistance ASTM E84-01 ASTM D522, 180° bend, 1/2" mandrel Flexibility Flexural Strength Humidity Resistance Drying time is temperature, humidity, and lm thickness dependent. Shelf Life: Flash Point: Clean Up: 12 months, unopened Store indoors at 40°F (4.5°C) to 100°F (38°C) >212°F (>102°C), mixed (ASTM D56) R6K10 (MEK) or R7K104 Maximum Elongation Prohesion Salt Fog Resistance www.sherwin-williams.com/protective ISO 178 ASTM D4585, 1000 hrs. ASTM D4585, 2000 hrs. ISO/R 527 ASTM G85, 2000 hours ASTM B117, 1000 hours ASTM B117, 2000 hours Rating 10 per ASTM D714 for blistering; Rating 10 per ASTM D610 for rusting Ratio of 74-101%, for edge radius from 0.1 mm to 2.4 mm, respectively. ES301K+ES301S system ~1,422 x 106 psi (100,000 KgF/cm2) Rating A Passes 9245 psi (650 KgF/ cm2) ASTM D1654, Rating:10 No defects 3% Passes D1654: Rating: 10 No defects continued on back

Protective & Marine Coatings EURONAVY ES301L / ES301K MOISTURE TOLERANT SOLVENT-FREE EPOXY PART A: PART B: PART A: PART B: STANDARD VERSION LOWER TEMP VERSION N02MIL-K SERIES N02CA301K N02MIL-L SERIES N02CA301L PRODUCT INFORMATION 9.59 SURFACE PREPARATION RECOMMENDED SYSTEMS Dry Film Thickness / ct. Mils (Microns) Surface must be clean and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion. Immersion or Atmospheric 1-2 cts. EURONAVY ES301L or K 4.0-6.0 1 ct. EURONAVY ES301S (optional) 4.0-6.0 (100-150) (100-150)...

EURONAVY ES301L / ES301K Protective & Marine Coatings MOISTURE TOLERANT SOLVENT-FREE EPOXY STANDARD VERSION LOWER TEMP VERSION PART A: PART B: PART A: PART B: N02MIL-K SERIES N02CA301K N02MIL-L SERIES N02CA301L APPLICATION BULLETIN APPLICATION PROCEDURES 9.59 PERFORMANCE TIPS Surface preparation must be completed as indicated. Stripe coat all crevices, welds, and sharp angles to prevent early failure in these areas. Mixing Instructions: Mix paint thoroughly to a uniform consistency When using spray application, use a 50% overlap with each pass with low speed power agitation prior to use. of...