DOD-E-24607A Protective & Marine Coatings CHLORINATED ALKYD ENAMEL N41-100 SERIES Revised 7/10 9.37 PRODUCT DESCRIPTION RECOMMENDED USES CHLORINATED ALKYD ENAMEL is a semi-gloss enamel, designed primarily for interior industrial and marine applications. For use over prepared substrates in marine and industrial environments: • Flame resistant - will not spontaneously burst into ame in the event of exposure to re • Complies with performance characteristics of DOD-E-24607 • Marine vessels - Interior - Crew quarters • Off shore platform interiors PERFORMANCE CHARACTERISTICS PRODUCT CHARACTERISTICS Finish: Semi-gloss • Flame Resistant Color: Various Fed. 595 colors available • Complies with performance characteristics of DOD-E-24607 Volume Solids: 59.6% ± 2%, may vary by color Color (depending on color) Weight Solids: 79.3% ± 2%, may vary by color VOC (EPA Method 24): Pure White 340 g/L; 2.8 lb/gal, maximum Product/Rex Number N41-100 Series Recommended Spreading Rate per coat: Wet mils (microns) Dry mils (microns) ~Coverage sq ft/gal (m2/L) Minimum 2.5 63 1.5 40 480 11.8 Maximum 3.5 88 2.0 50 640 15.7 Theoretical coverage sq ft/gal 960 23.5 (m2/L) @ 1 mil / 25 microns dft NOTE: Brush or roll application may require multiple coats to achieve maximum lm thickness and uniformity of appearance. Drying Schedule @ 2.0 mils wet (50 microns): @ 50°F/10°C To touch: Dry hard: To recoat: To cure: @ 77°F/25°C 50% RH @ 100°F/38°C 3 hours 8 hours 10 hours 14 days 2 hours 6 hours 6-8 hours 14 days 30 minutes 5 hours 5 hours 7 days Drying time is temperature, humidity, and lm thickness dependent. Shelf Life: Flash Point: Reducer: Clean Up: 12 months, unopened Store indoors at 40°F (4.5°C) to 100°F (38°C) 100°F (38°C) SETA Flash Not recommended Mineral Spirits, R1K4 www.sherwin-williams.com/protective continued on back

DOD-E-24607A Protective & Marine Coatings CHLORINATED ALKYD ENAMEL N41-100 SERIES PRODUCT INFORMATION SURFACE PREPARATION RECOMMENDED SYSTEMS Dry Film Thickness / ct. Mils (Microns) Steel 1 ct. TT-P-645 1-2 cts. DOD-E-24607 1.75-3.5 (42-88) 1.5-2.0 (40-50) Steel, alkyd primer: 1 ct. Kem Kromik Universal Metal Primer 2.5-3.5 (63-88) 2 cts. DOD-E-24607 1.5-2.0 (40-50) Aluminum: 1 ct DTM Wash Primer 2 cts. DOD-E-24607 9.37 0.7-1.3 (18-32) 1.5-2.0 (40-50) Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate...

DOD-E-24607A Protective & Marine Coatings CHLORINATED ALKYD ENAMEL N41-100 SERIES APPLICATION BULLETIN APPLICATION PROCEDURES 9.37 PERFORMANCE TIPS Surface preparation must be completed as indicated. Stripe coat all crevices, welds, and sharp angles to prevent early failure in these areas. Mixing Instructions: Mix paint thoroughly with low speed power When using spray application, use a 50% overlap with each pass agitation prior to use. of the gun to avoid holidays, bare areas, and pinholes. If necessary, Apply paint at the recommended lm thickness and spreading cross spray at a right angle....