Seajet Pellerclean Application Manual

Product catalog summary

Introduction
Pellerclean is a biocide-free, foul-release coating designed for propellers and stern gear. It consists of a two-component epoxy primer and a one-component silicone coating, providing protection against marine growth in both fresh and saltwater environments.

Specifications
The product is available in two kit sizes: a small kit (315 ml) sufficient for 0.7m² and a big kit (1750 ml) sufficient for 3.88m². The kits include Seajet Pellerclean Primer Base, Primer Hardener, and Clear Coat.

Application Procedure

Step 1: Surface Treatment - Remove contamination and existing coatings using a scraper, abrasive paper, and pads. Rinse with fresh water.
Step 2: Creating a Surface Profile - Abrade the substrate with P80-120 grade abrasive paper and clean with Seajet Thinner. Avoid touching the substrate without gloves.
Step 3: Application Primer - Stir the Pellerclean Primer Base, mix with Primer Hardener, and apply two coats. Maintain a maximum overcoating interval of 7 days and a drying time of 15-30 minutes between coats.
Step 4: Application Clear Coat - Apply at least two coats of Pellerclean Clear Coat, with a 30-minute interval between coats.

Repair and Recoating
For intact systems, re-coat after washing with fresh water. Do not apply primer over the clear coat. Re-coating may be necessary annually in high cavitation areas.

Success Factors
Ensure thorough surface treatment and apply only in dry conditions with temperatures above 5°C and humidity below 85%. Drying time before launch is 8 hours at 20°C, or overnight at 5°C.

Environmental and Safety Considerations
Dispose of brushes, paint cans, and other materials according to local regulations. Avoid contamination of other areas with silicone from the clear coat.

Contact Information
Seajet is part of Chugoku Paints B.V., located in the Netherlands. For more information, visit seajetpaint.com or contact them at +31-167-526-100.

Catalog excerpts

LONG PROTECTION FUEL SAVINGS

Open the catalog to page 1

Pellerclean is a biocide free, foul-release coating for propeller and stern gear. Pellerclean consists of two-component epoxy primer and one-component silicone coating providing foul-release properties against marine growth in both fresh and salt water. Fouling may adhere; however, this will be removed by water friction or gentle washing with a sponge. Step 1 Surface treatment Remove all contamination and any existing coating from the substrate by using a combination of scraper, abrasive paper, and abrasive pads. Rinse with fresh water to remove dust. Step 3 Application Primer Step 2 Creating...

Open the catalog to page 2

For the parts where to clear coat came off due to cavitation, please sand, degrease and apply the clear coat again on the primer. Success Factors Application Clear Coat Apply a minimum of two coats of Pellerclean Clear Coat. The second coat may be applied 30 minutes after the first. To obtain maximum performance, use all Pellerclean Clear Coat provided in the kit. For re-coating existing Pellerclean: If the existing system is intact, you may re-coat after fresh water washing. Do not apply primer over clear coat. Re-coating may be required annually at high cavitation areas. Take special care with...

Open the catalog to page 3

Small kit, total content 315 ml • 1 x SEAJET PELLERCLEAN PRIMER BASE • 1 x SEAJET PELLERCLEAN PRIMER HARDENER • 1 x PELLERCLEAN CLEAR COAT • 2 x SEAJET PELLERCLEAN PRIMER BASE • 2 x SEAJET PELLERCLEAN PRIMER HARDENER • 1 x PELLERCLEAN CLEAR COAT • Quantity in small kit is sufficient to treat 0.7m2. • Quantity in big kit is sufficient to treat 3.88m2. PRIMER + CLEAR COAT all metal underwater parts underwater lightbulbs, transducers and plastic bow thrusters OFFERED BY THE WORLD LARGEST SILICONE PAINT PRODUCER FOR PROPELLERS AND STERN GEAR Seajet is part of Chugoku Paints B.V. Sluisweg 12, 4794...

Open the catalog to page 4

Seajet Pellerclean Application Manual

Seajet Pellerclean Application Manual

Catalog excerpts

All SEAJET catalogs and brochures