Seajet Triple-Pack
5Pages

SEAJET TRIPLE PACK Product description Seajet Triple Pack is a self-polishing coating suitable for propellers, stern gear and trim tabs. The Triple Pack is an all-in-one product. This coating lasts for one season. Seajet Triple Pack is suitable for motorboats and sailing yachts up to 40 knots. Suitable for aluminium, stainless steel and alloy. Product data Pack sizes Epoxy primer & very high performance, self-polishing antifouling paint. SEAJET 114 PROPELLER PRIMER: Please revert to attached Technical Data Sheet. SEAJET 034 EMPEROR A: Please revert to attached Technical Data Sheet. Surface preparation Step 1: Remove all contamination and old antifouling from the surface to be coated. Use a combination of scraping, abrasive paper and abrasive pads. Fresh water wash. Step 2: For bronze, aluminium and stainless steel surfaces: Key the surface using P80 grade wet and dry abrasive. For factory coated outdrives and stern gear: P-180 abrasive paper is recommended to provide a physical key. Step 3: Take care to rub the surface to be painted with a thinner, such as acetone, to clean off any possible residue. Step 4: Mix SEAJET 114 PROPELLER PRIMER Component A with Component B. Add Component B to the base (Component A) whilst stirring. Stir well before use or 5 minutes. Apply the mixed product SEAJET 114 PROPELLER PRIMER first to the edges of the propeller by brush assuring good cover age and then apply 1 coat all over by brush. Dispose of the mixed product carefully when finished. Step 5: Minimum of 10 hours (at 15°C) after the application of primer it has to be over coated with 2 coats of SEAJET 034 EMPEROR A. Stir SEAJET 034 EMPEROR A before use for 5 minutes and apply 1 coat of SEAJET 034 EMPEROR A over the full surface of the propeller. Step 6: After application of the 1st coat of SEAJET 034 EMPEROR A allow a minimum of 6-7 hours (at 15°C) before applying the 2nd coat of SEAJET 034 EMPEROR A. Leave to dry for a minimum of 15 hours before launching (at 15°C). Maximum interval before launching is 6 months. Leave to dry for a minimum of 15 hours before launching (at 15°C). Maximum interval before launching is 6 months. General information Storage Store the containers in a dry, cool and well ventilated space and away from direct sunlight. Containers must be kept firmly closed. Handle with care. Transportation The product should stay in a securely closed container during transport. Shelf life Disposal Do not empty into drains, dispose of this material and its container at hazardous or special waste collection point. Additional information More information can be found on www.seajetpaint.com. Safety information Personal Protection advice and additional information can be obtained from the product Safety Data Sheet from Chugoku Paints B.V. which is available on request. The minimum safety precautions in dealing with this paint are: a. Observe the precautionary notices displayed on the container. b. Provide adequate ventilation. c. Avoid skin contact and inhalation of spray mist and vapours. d. If the product comes into contact with the skin, wash thoroughly with luke warm water and soap or suitable cleaner. If the eyes are contaminated, irrigate with water and seek medical advice immediately. e. Since the product contains flammable materials, keep away from sparks and open flames. No smoking should be permitted in the area. Disclaimer Data, specifications, directions and recommendations given in this data sheet represent test results or experience obtained under controlled or specially defined circumstances.Their accuracy, completeness or appropriateness under the actual conditions of any intended use is not guaranteed and must be determined by user. Product data is subject to change without notice and automatically void two years from issue. All legal relations of Chugoku Paints B.V. will be governed by the Uniform Terms of Sale and Delivery of Chugoku Paints B.V. as last filed with the district court of Rotterdam and upon request they will be made available without charge. Chugoku Paints B.V. explicitly rejects the applicability of any General Conditions, which its contractual parties may use. Exclusive jurisdiction: competent Court in Rotterdam. Some products have been specially modified to adapt to specific European requirements with regard to European-, national- and local laws and regulations or with regards to specific European use requirements. As a result some physical properties in a TDS may differ from those given in the original Japanese TDS.

SEAJET 114 PROPELLER PRIMER Product description SEAJET 114 PROPELLER PRIMER is an epoxy primer that maximises adhesion to aluminium and alloys. It offers superior performance to etching primers and can be used above and below water, on stern gear, outboard legs, propellers, trim tabs etc. Product data Colour Flash point Volume solids % Pack sizes Mixing ratio Application details Thinner Application methods Airless spray, brush, roller* Ambient temperature Product temperature Substrate temperature Paint output pressure: Spray details Spreading rate Recommended film thickness Wet (µm) 100 per...

SEAJET 114 PROPELLER PRIMER Drying / overcoating data Drying time Overcoating interval Surface dry:60 min Hard dry: 12 hours Induction time Surface dry:45 min Hard dry: 8 hours Surface dry:30 min Hard dry: 6 hours Surface dry:20 min Hard dry: 4 hours General information Storage Store the containers in a dry, cool and well ventilated space and away from direct sunlight. Containers must be kept firmly closed. Handle with care. Transportation The product should stay in a securely closed container during transport. Shelf life Min. 3 years @ 20°C Disposal Do not empty into drains, dispose of...

SEAJET 034 EMPEROR A Product description Seajet 034 Emperor A is a high performance self polishing antifouling, suitable for aluminium. Ideal for club racers as it can be burnished during the season. Available in bright colours. No risk of galvanic corrosion on aluminium surfaces. Product data Colour White, mid blue, navy blue, bright red, black Flash point Volume solids % Pack sizes Mixing ratio Application details Thinner Application methods Brush, roller Ambient temperature Product temperature Substrate temperature Paint output pressure: Spray details Spreading rate Recommended film...