Revision date: April 2019 Technical Data Sheet Semi-Hard Ablative Antifouling 6000 Series Semi-Hard Hybrid Ablative • Durable Semi-Hard Antifouling Paint • Used on All Types of Vessels • Dependable Performance PRODUCT DESCRIPTION Talon is a copper-based, semi-hard PRODUCT INFORMATION hybrid ablative antifouling paint. Talon Colors: Black 6045, Blue 6042, Dark Blue 6030, Red 6041, Green 6043 can be applied over most antifouling Finish/Sheen: Semi-Gloss coatings and aggressively combats all Copper Content: 33.6% all colors (628 g/l) types of fresh and salt water marine Shipping Weight: Black - 15.53 Lbs/Gal (7.04 kg/Gal) Blue - 15.58 Lbs/Gal (7.06 kg/Gal) Red - 15.99 Lbs/Gal (7.25 kg/Gal) Dark Blue - 15.74 Lbs/Gal (7.13 kg/Gal) Green - 15.39 Lbs/Gal (6.98 kg/Gal) *All colors are not available in all states Flash Point: 100°F (38°C) VOC: 398 Grams/Liter Typical Film Thickness: Pleasure craft: 2.5 mils (63.5 µ) dry film thickness (DFT) per coat, (4.5 mils (114.3 µ) wet film thickness (WFT)), 2 coats on entire hull and a 3rd at the waterline and other high wear areas. Pleasure craft (California/Reduced CU2O Leach Rate Application): 2.5 (63.5 µ) mils dry film thickness (DFT) per coat, (4.5 mils (114.3 µ) wet film thickness (WFT)), 2 coats on entire hull. Commercial Marine: 3.0-5.0 mils (76.2-127 µ) DFT per coat by spray application (5.4-8.9 mils (137.16-226.06 µ) WFT), 2 coats on entire hull and a 3rd at the waterline and other high wear areas. Theoretical Coverage: 359 sq.ft./gal. (33.35 m2) at 2.5 mils (63.5 µ) dry film thickness Shelf Life: 30 months when stored under cool, dry conditions FEATURES & BENEFITS • Value-priced semi-hard hybrid ablative antifouling • 33.6% (628 g/l) cuprous oxide – highest grade available • Consistent viscosity providing better flow and rolling ability (Page 1 of 3) NEW NAUTICAL COATINGS, INC. 14805 49th Street North • Clearwater, FL 33762 • 727.523.8053 • 800.528.0997 • FAX 727.5

Technical Data Sheet Aluminum: TALON Antifouling paint may be used on an aluminum hull only when used with the proper barrier coat system described in Technical Bulletin AL1284. TALON is not to be used on bare aluminum. • May be applied over other modified epoxy antifouling paints APPLICATION DETAILS Method: This product may be applied by airless and conventional spray, solvent resistant rollers and brushes. Dry Times and Overcoating Intervals: Pleasure Craft Drying Time in Hours Substrate Temp. Overcoating Time Please contact your Sea Hawk representative for Commercial Marine application and...

Technical Data Sheet guideline of the coating and proper coating application procedures. As application, environmental and design factors can vary significantly due care should be exercised in the selection, verification of performance, and use of the coating. APPLICATION DATA Mixing: TALON bottom paint contains a moderate concentration of copper oxide and may have settled in transit. Product must be thoroughly mixed with power mixer/shaker until uniform. Additives: You may add a pint of BIOCOP TF for dual-biocide protection. Induction Time: Not Applicable Thinning: If necessary, maximum 10%...