Catalogs >
Sea Hawk >
Cukote

Cukote
2Pages

Catalog excerpts

SeaXJ^ Hawk^T PREMIUM YACHT FINISHES Self-Polishing Copolymer Antifoulant • Semi-hard, self-polishing ablative finish • Multi-season performance • Removing boat from water does not affect antifouling properties • No TBT (organotin compounds) • 47.5% cuprous oxide • Effective below the waterline on fiberglass, steel and wood vessels • Lloyd's Registry certified Product Description Cukote's high loading of cuprous oxide makes this formulation a top performer, even in the most severe fouling areas. As an ablative, self-polishing coating, there is no buildup of bottom paint over time. Your hull’s underwater surface remains smooth and clean. Cukote copolymer can also withstand removal from water without affecting its antifouling properties. Cukote is the premium self-polishing antifouling paint that has established the standard in the industry. Product Information Colors Available: Red 3441, Blue 3442, Green 3443, Black 3445, Dark Blue 3430, Shark White 3410, Burgundy 3428, Brown 3432, Teal 3434 Finish/Sheen: Semi-Gloss Converter: One Pack Copper Content: 47.57% All Colors Solids by Weight: 81% (±2%) Volume Solids: 54% (±2%) Mix Ratio: One Pack Shipping Weight: 18-20 Lbs./Gal. Flash Point: 100°F VOC: 398 Grams/Liter Typical Film Thickness: Pleasure Craft: 2.5 mils dry film thickness (DFT) per coat by roller application (4.6 mils wet film thickness (WFT) Commercial Marine: Average 4.0-5.0 mils DFT per coat by spray application (7.4-9.3 mils WFT) Theoretical Coverage: 173 Sq.Ft. @ 5.0 mils DFT, 346 Sq. Ft. @ 2.5 mils Recommended Coats: 2 Full Coats with 3 at the water line and other high wear areas, depending on intended service. Features and Benefits • Self Polishing Ablative with Multi-Season Performance on Both Pleasure Craft, Coastal and Deep Sea Vessels • Harder Ablative Finish Makes Cukote Ideal for Fast Moving Vessels including: Pleasure Craft Power Boats, High Speed Transports, Supply Vessels, and Ferries • May Be Taken In and Out of the Water Without Affecting Antifouling Characteristics • Does Not Contain Any Organotin Compounds (TBT) • May Be Used on All Steel, Fiberglass, and Wood Vessels Below the Waterline That Have Been Planned Drydockings of Less Than Three Years Application Controls Method: Airless and Conventional Spray, Solvent Resistant Rollers and Brushes. Dry Times and Overcoating Intervals: Pleasure Craft Drying time in Hours Limitations: Apply in good weather when air and surface temperatures are above 50°F (10°C). Surface temperature must be a least 50°F (10°C) above dew point. For optimum application properties, bring material to 70-80°F (21-27°C) temperature range prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage between 40° and 100°F (4-38°C). Prolonged atmospheric exposure of this product may detract from performance. Technical and application data herein is for the purpose of establishing a general guideline of the coating and proper coating application procedures. As application, environmental and design factors can vary significantly due care should be exercised in the selection, verification of performance, and use of the coating. NEW NAUTICAL COATINGS, INC. 14805 49th Street North • Clearwater, FL 33762 • 727.523.8053 • 800.528.0997 • FAX 727.523.7325

Open the catalog to page 1

Surface Preparation Paint only clean, dry surfaces. Remove all grease, oil, wax, or other foreign material by solvent or detergent washing. (SSPC-SPI) Self-Polishing Premium Performance Compatibility: For pleasure craft applications, please refer to our Sea Hawk Compatibility Chart to ensure compatibility when applying Cukote antifouling paint over existing bottom paint. Previously Painted Surfaces: Cukote is suitable for this substrate. For correct procedures please refer to the Application Guidelines for Fiberglass/Gelcoat. Fiberglass or Vinyl Ester Hulls: Cukote is suitable for this...

Open the catalog to page 2