Aluma Hawk - 2 Pages

Add to MyNauticExpo favorites
Aluma Hawk

Catalog excerpts

Aluma Hawk™ Revision date: September 2014 Technical Data Sheet Rust-Inhibiting and Lift-Resistant to Lacquer/Enamel Based Topcoats Aluminum Boat Paint Use Above and Below the Waterline • Excellent adhesion on aluminum • Use as a primer and or topcoat on raw aluminum, fiberglass and other substrates • One-Step application ideal for pontoon boats and jon boats • Safe for fresh or saltwater submersion PRODUCT DESCRIPTION Aluma Hawk is a quick-dry, highsolids, corrosion-inhibiting coating designed for use on aluminum with no need of additional primers. Aluma Hawk is chromate-free and may be used above or below the waterline. Aluma Hawk’s unique dual purpose phenolic resin, allows it to be used as a primer directly on metal with or without a topcoat. NOTE: Contains no antifouling characteristics PRODUCT INFORMATION Colors: Jon Boat Green, Aluminum Gray and Black Typical Shelf Life: Recommended Coats: 2 Coverage: Film thickness: Solids by volume: 47-49% Solids by weight: 70-71% FEATURES AND BENEFITS • Rapid air dry • Lift-resistant to lacquer, enamel and acrylic topcoats • Chromate-free • Excellent water and oil hydrocarbon resistant DRY TIME (HOURS) 50ºF/10ºC To Touch To Recoat To Overcoat Consult your Sea Hawk Representative for the system best suited for surfaces to be protected LIMITATIONS This product should be maintained in protected storage between 40° and 100°F (4-38°C). Exposure to air and extremes of temperature (Page 1 of 2) NEW NAUTICAL COATINGS, INC. 14805 49th Street North • Clearwater, FL 33762 • 727.523.8053 • 800.528.0997 • FAX 727.523.7325 • www.SeaHawkPaints.com

 Open the catalog to page 1

Aluma Hawk™ AH7000 Series Technical Data Sheet should be avoided. Keep out of direct sunlight. Technical and application data herein is for the purpose of establishing a general guideline of the coating and proper coating application procedures. As application, environmental and design factors can vary significantly due care should be exercised in the selection, verification of performance, and use of the coating. SURFACE PREPARATION UNPAINTED ALUMINUM: The surface must be dry and free of grease, wax, dirt or other contaminants. Sand with 80 grit sandpaper and clean. Wipe down with white...

 Open the catalog to page 2

All Sea Hawk catalogs and brochures

  1. CUKOTE 330 VOC

    3 Pages

  2. AF-33

    2 Pages

  3. Cukote

    2 Pages

  4. Islands 77 Plus

    2 Pages

  5. Mission Bay CSF

    2 Pages

  6. Mission Bay

    2 Pages

  7. Smart Solution

    2 Pages

  8. Biocop TF

    3 Pages

  9. Gel Coat

    2 Pages

  10. S-90

    1 Pages

  11. Silver Bullet?

    2 Pages

  12. sHAWKocon?

    2 Pages

  13. S-76

    2 Pages

  14. S-75 and S-75C

    2 Pages

  15. Tuff Stuff

    3 Pages

  16. Hawk Filler

    2 Pages

  17. BiocopTF

    3 Pages

  18. Hawks Grip

    2 Pages

  19. Tin Booster

    1 Pages

  20. Bio-Boost

    1 Pages

  21. Talon

    2 Pages

  22. Sharkskin

    2 Pages

  23. Monterey

    2 Pages

  24. Cukote Biocide

    2 Pages

Archived catalogs

  1. Brochure

    20 Pages