Technical Data Sheet Self-Polishing Copolymer Antifouling Revision date: April 2019 Self-Polishing Premium Performance • Multi-season performance • Removing boat from water does not affect antifouling properties • 47.5% cuprous oxide • Lloyd’s Register certified PRODUCT DESCRIPTION CUKOTE 330 Grams/Liter VOC is a top-performing antifouling coating, even in the most severe fouling areas, and preserves air quality with its Low VOC emissions during application. Its unique ablative, self-polishing properties keeps boat hull’s underwater surfaces smooth and clean with no buildup of bottom paint over time. Effective below the waterline on fiberglass, steel and wood vessels, CUKOTE 330 Grams/Liter VOC provides multi-season antifouling protection with its advanced formulation allowing vessels to be removed from the water without compromising its antifouling characteristics. PRODUCT INFORMATION Colors Available: Black 3445-L, Red 3441-L, Blue 3442-L, Dark Blue 3430-L, Teal 3434-L Finish/Sheen: Semi-Gloss Converter: One Pack Copper Content: 47.57% All Colors Solids by Weight: 81% (±2%) Volume Solids: 54% (±2%) Mix Ratio: One Pack Shipping Weight: Black - 18.3 Lbs/Gal (8.3 kl/Gal) Red - 18.8 Lbs/Gal (8.52 kl/Gal) Blue - 18.2 Lbs/Gal (8.25 kl/Gal) Dark Blue - 18.0 Lbs/Gal (8.16 kl/Gal) Teal - 18.1 Lbs/Gal (8.21 kl/Gal) *All colors are not available in all states Flash Point: 100°F VOC: 330 Grams/Liter Typical Film Thickness: Pleasure craft: 2.5 mils (63.5 µ) dry film thickness(DFT) per coat, (4.6 mils (116.84 µ) wet film thickness(WFT)), 2 coats on entire hull Pleasure craft (California/Reduced CU2O Leach Rate Application): 2.5 mils (63.5 µ) dry film thickness (DFT) per coat, (4.6 mils (116.84 µ) wet film thickness (WFT)), 2 coats on entire hull Commercial Marine: 4.0-5.0 mils (101.6-127 µ) DFT per coat by spray application (7.4-9.3 mils (187.96-236.22 µ) WFT), 2 coats on entire hull Theoretical Coverage: 173 Sq.Ft. (16.07 m2) at 5.0 mils DFT, 346 Sq. Ft. (32.14 m2) at 2.5 mils (63.5 µ) FEATURES AND BENEFITS • Self Polishing Ablative with Multi-Season Performance on Both Pleasure Craft, Coastal and Deep Sea Vessels • Harder Ablative Finish Makes CUKOTE 330 Grams/Liter VOC Ideal for Fast Moving Vessels including: Pleasure Craft Power Boats, High Speed Transports, Supply Vessels, and Ferries • May Be Taken In and Out of the Water Without Affecting Antifouling Characteristics • Does Not Contain Any Organotin Compounds (TBT) • May Be Used on All Steel, Fiberglass, and Wood Vessels Below the Waterline That Have Been Planned Dry Dockings of Less Than Three Years APPLICATION DETAILS NEW NAUTICAL COATINGS, INC. 14805 49th Street North • Clearwater, FL 33762 • 727.523.8053 • 800.528.0997 • FAX

Dry Times and Overcoating Intervals: Pleasure Craft Drying time in Hours (on reverse side) Substrate Temp. Minimum Launch Time N/A 12 hours 12 hours Consult your Sea Hawk Representative for the system best suited for surfaces to be protected. Apply in good weather when air and surface temperatures are above 50° F (10° C). Surface temperature must be a least 5° F (1° C) above dew point. For optimum application properties, bring material to 70-80° F (21-27° C) temperature range prior to mixing and application. Unmixed material (in closed containers) should be maintained in protected storage between...

Technical Data Sheet Conventional Spray: Please contact your Sea Hawk representative for more specific information. Prior to use, obtain and consult the “Safety Data Sheet” of this product for health and safety information. Read and observe all precautionary notices on container labels. NEW NAUTICAL COATINGS, INC. 14805 49th Street North • Clearwater, FL 33762 • 727.523.8053 • 800.528.0997 • FAX 727.523.7325 • www.SeaHaw