CUTTING AND WELDING
15Pages

Technical Diving Equipment Cutting & Welding

Technical Diving Equipment **JQ¡ 'POMMEC WELDING LENS' Pommec welding lenses are designed for several different Masks, helmets and constant volume hoods. These assembly's are specially designed to provide visual protection only while welding and cutting underwater. Mounting of these lenses is very simple and all mountingcomponents will be delivered with the lens. The big advantage of the Pommec welding lens is that the complete face plate of every mask and helmet is 100% protected against welding and cutting Face protection plates are available in clear and dark Pom-WL-AH Dark welding lens...

Technical Diving Equipment **JQ¡ BROCO UNDERWATER WELDING represented a major break- electrodes. At long last certifiable welds could be obtained with minimal amounts of physical labor, diver training and wet welding Less experienced divers can do the work right with less qualification training when Broco electrodes are used. For many non-structural repairs the resultant weld is allowed more leeway in terms of porosity, inclusions, integrity and appearance. In these instances welder/diver pre- qualification to the job is often not required. This environment has led to the proliferation of...

Technical Diving Equipment **JQ¡ SofTouch mild steel electrodes are available in 3/32 inch, 1/8 inch, 5/32 inch and 3/16 inch diameters. Stainless electrodes are sold in 1/8 inch and 5/32 inch sizes. SofTouch Wet Welding Electrodes are sealed in a Mil-Spec foil pouch to electrodes are then packaged in a rigid resealable plastic tube which provides maximum protection. The secret behind the reliability and ease of operation of the SofTouch electrode is its proprietary formulation for the flux enhancing coating. Only Broco offers BroCote. It's the modern flux coating that makes this electrode...

Technical Diving Equipment BROCO ULTRATHERMIC CUTTING Underwater Ultrathermic Since then, Broco's engineers have been constantly refining the torch and rods, making subtle changes to ensure optimum maximum safety under all more cutting offshore is done with Broco. Cut sheet pile, remove tubular supports or trim damaged hull plates. Slag-free gouging means easy weld removal and edge preparation. ANU (Approved for Navy Use) designated and featured in the U.S. Navy's "Underwater Cutting and Welding" manual, the Broco Underwater Ultrathermic Cutting System is used by navies around the world....

Technical Diving Equipment iJ¡¡* Oxygen Regulator is a multi- stage unit delivering the constant flow and high underwater burning. Broco research has shown cutting efficiency depends more on oxygen flow than oxygen pressure, so the Broco High- Volume Regulator is offered to meet this basic requirement. Designed and manufactured for ease of operation, maximum efficiency, and years of rugged use, the Broco High-Volume Oxygen Regulator is Underwriters Laboratories Burning in excess of 10,000 degrees Fahrenheit at the tip, Broco Underwater Ultrathermic Cutting Rods cut or melt virtually any...

Technical Diving Equipment BROCO BR-22 UNDERWATER OXYGEN-ARC CUTTING TORCH, ASSEMBLY

Technical Diving Equipment **JQ¡ RAPIDFIRE CUTTING ROD IGNITOR RapidFire® cutting rod igniters are an expedient means of igniting an exothermic torch without the requirement for an auxiliary 1 2 volt battery. The RapidFire® cartridge is unique to Broco® and the key to the lightweight portability 1. Fit RapidFire® igniter cartridge to end of 3. Introduce light oxygen flow. 2. Press against hard surface to break seal. 4. Within 5 seconds cutting rod ignition is

Technical Diving Equipment KERIE CABLE THERMAL ARC CUTTING EQUIPMENT The cutting or oxidising of mild steel (iron) etc. is made possible by the fact that all mild steel (iron) is a very good fuel provided that sufficient heat and oxygen are available to keep it burning. Just as wood and paper will burn in oxygen if a flame is applied so will steel, in wire wool form. All combustible materials have their kindling or burning points, mild steel (iron) being approximately 870° centigrade. When iron is made harder and stronger by the inclusion of carbon, chrome etc., it becomes more difficult to...

Technical Diving Equipment **JQ¡ PENSON CUTTING TORCH Working in water demands specially adapted equipment that is designed to operate under extreme conditions. The development of effective underwater cutting torches calls for practical diving experience and dedicated technical know-how. Penson has the technical knowledge and diving experience required to develop truly effective cutting torches. The Penson underwater cutting torches are the result of extensive practical testing. The Penson underwater cutting torch is the result of more than 10 years of development and testing under highly...

Technical Diving Equipment **JQ¡ Its unique design allows for complete dismantling and replacement of all parts, on site, without the need for any special tools or training. The holder can also be adjusted for wear through its patented design, which allows the main collet body to be turned. Each full revolution moves the body up 1.0mm allowing for over 10mm of adjustment to be made. It has an overall length of 200mm (8"), a diameter of 40mm (11/2"). It's light (under 400g) and easy to use with a simple twist mechanism to tighten and release electrodes. It's manufactured from a tough,...

Technical Diving Equipment Assembly Instructions & Spare Part 1 : Place roble retainer UW5DCM Over vcur weldir-g cabla. (If illnger supphod i*nh whi(j leiOcJ ulrvrjdy finad, ignor* ihis intlruction). 2: Fii welding coble imo coble connecror, UWMÛb and tlghltn the two stainless sled grub Scrom. F n',n'fi coble covering is cut badie to 3; Remove Securing piti UW50Ö3A fron-, rnflin body- Take note oí milled slol in fide of coble connector UW50O5 as Ihii ii where rhe jecurlng pin sin. to rncilio SCCurC ■. : ■!■*. :: i,i. i IÍLM "i :i iimn hAdf uniti slol cornei mio no» ihnough securing pinhole....