Hydrocoat SR
2Pages

{{requestButtons}}

Catalog excerpts

Hydrocoat SR - 1

Hydrocoat SR® Dual-Biocide , Water-Based, Ablative TECHNICAL BULLETIN 1847 9/12 The world’s first dual-biocide, water-based, ablative bottom paint Dual-Biocides provide outstanding multi-season protection Ablative, self-polishing technology eliminates sanding and paint build-up Easy to apply and cleans up with soap & water Hydrocoat SR takes the Hydrocoat name to a whole new level of performance and environmental consciousness. Pettit’s Clean Core Technology is combined with an organic algaecide to offer outstanding protection against hard and soft fouling, while lowering the paint’s environmental impact. Hydrocoat SR uses innovative technology to replace the harsh solvents found in most bottom paints with water, providing an easier application and clean up, with low VOC’s and no heavy solvent smell. Hydrocoat SR’s self-polishing surface wears away with use, exposing fresh biocides, while eliminating the need for sanding and paint film build up. Hydrocoat SR holds up to trailering, beaching, and launching. Its unique formula allows unlimited dry time to launch, so you can paint in the fall or winter. 1247 Blue PHYSICAL DATA VEHICLE TYPE: Water-Based Emulsion FINISH: Flat COLORS: 1247 Blue 1647 Red 1847 Black COMPONENTS: 1 CURING MECHANISM: Solvent Release SOLIDS (theoretical): By weight...73 +/- 2% By volume...40 +/- 2% COVERAGE: 430 sq. ft/gal. VOC: 150 g/l max. (1.25 lbs/gal) ACTIVE INGREDIENTS: Cuprous Oxide...40% N-Cyclopropyl-N’(1,1-dimethyethyl)-6(methylthio)1,3,5 triazine-24-diamine...2.00% FLASH POINT: None APPLICATION DATA METHOD: Brush, roller, airless or conventional spray. NUMBER OF COATS: 2 minimum with additional coat at waterline recommended. DRY FILM THICKNESS PER COAT: 1.5 mils (3.75 wet mils) APPLICATION TEMP: 50° F. Min. / 90°F. Max. DRY TIME* (HOURS): To Touch To Recoat To Launch 90°F 1/4 1-1/2 12 70°F 1/2 3 16 50°F 1 6 48 *The above dry times are minimums. Hydrocoat SR may be recoated after the minimum time shown. There is no maximum dry time before launching. THINNER: Water Note: Color differences may occur between actual and color chips shown ASSOCIATED PRODUCTS 92 Bio-Blue Hull Surface Prep 95 Fiberglass Dewaxer 6998 Skip-Sand Primer 4700/4701 High-Build Gray Epoxy Primer 4100/4101 High-Build White Epoxy Primer 6455/044 Metal Primer 6627 Tie-Coat Primer 6980 Rustlok Steel Primer 120 B

Open the catalog to page 1
Hydrocoat SR - 2

Hydrocoat SR® Dual-Biocide , Water-Based, Ablative Antifouling APPLICATION INFORMATION Hydrocoat SR contains cuprous oxide. As a result, there is a tendency for settling to occur, especially if the paint has been on the shelf for several months. It is necessary to thoroughly mix the paint before using. If possible, shake the can of paint on a mechanical paint shaker. Before using, check the sides and bottom of the can to make sure all the pigment has been mixed in. If mixing is going to be done with a wooden paddle or a n electric drill mixer, pour off half of the liquid from the top of the...

Open the catalog to page 2

All Pettit catalogs and brochures

  1. Pontoon Pro

    2 Pages

  2. Neptune5

    2 Pages

  3. Horizons®

    2 Pages

  4. SC - 21

    2 Pages

  5. Color Card

    6 Pages

  6. Ultima SR-40

    2 Pages

  7. Hydrocoat

    2 Pages

  8. Sealers

    2 Pages

  9. EZ Bilge

    2 Pages

  10. EZ Decks

    2 Pages

  11. Easypoxy

    2 Pages

Archived catalogs