Catalog excerpts
Hydrocoat Eco Copper-Free , Water-Based, Ablative TECHNICAL BULLETIN 1804 6/13 Water-based, copper-free, self-polishing ablative antifouling paint Dual-biocides provide outstanding multi-season protection in all conditions Uses the power of organic Econea for better protection and a greener earth Co-polymer ablative technology eliminates sanding and paint build-up Easy application and cleanup with soap & water Hydrocoat Eco is the newest member of Pettit’s exclusive water-based, copolymer ablative family of bottom paints. The highest level of metal-free Econea biocide available is combined with a powerful slime fighting inhibitor to provide unprecedented multi-season protection in the toughest marine environments. Innovative Hydrocoat Technology is used to replace the harsh solvents found in most bottom paints with water, providing an easier application and clean up, with low VOC’s, and no heavy solvent smell. Hydrocoat Eco’s co-polymer ablative paint film wears away with use allowing for a controlled release of biocides while eliminating paint build up and the need for sanding between coats. This copper-free formula is compatible over almost all bottom paints and is safe for use on all substrates including steel and aluminum. Hydrocoat Eco will not lose effectiveness when removed from the water. PHYSICAL DATA VEHICLE TYPE: Water-Based Emulsion FINISH: Flat COLORS: 1104 White - 1204 Blue - 1304 Green 1604 Red - 1804 Black COMPONENTS: 1 CURING MECHANISM: Solvent Release SOLIDS (theoretical): By weight...73 +/- 2% By volume...40 +/- 2% COVERAGE: 430 sq. ft/gal. VOC: 150 g/l max. (1.25 lbs/gal) ACTIVE INGREDIENTS: Econea (Tralopyril)...6.0% Zinc Pyrithione...4.8% FLASH POINT: None APPLICATION DATA METHOD: Brush, roller, airless or conventional spray. NUMBER OF COATS: 2 minimum with additional coat at waterline recommended. DRY FILM THICKNESS PER COAT: 1.4 mils (4.0 wet mils) APPLICATION TEMP: 50° F. Min. / 90°F. Max. DRY TIME* (HOURS): To Touch To Recoat To Launch 90°F 1/4 1-1/2 12 70°F 1/2 3 16 50°F 1 6 48 *The above dry times are minimums. Hydrocoat Eco may be recoated after the minimum time shown. There is no maximum dry time before launching. THINNER: Water Note: Color differences may occur between actual and color chips shown ASSOCIATED PRODUCTS 92 Bio-Blue Hull Surface Prep 95 Fiberglass Dewaxer 6998 Skip-Sand Primer 4100/4101 High Build Epoxy Primer White 4700/4701 High Build Epoxy Primer Gray 6455/044 Metal Primer 6627 Tie-Coat Primer 6980 Rustlok Primer
Open the catalog to page 1Hydrocoat Eco® Copper Free , Water-Based, Ablative Antifouling APPLICATION INFORMATION Hydrocoat Eco contains biocides. As a result, there is a tendency for settling to occur, especially if the paint has been on the shelf for several months. It is necessary to thoroughly mix the paint before using. If possible, shake the can of paint on a mechanical paint shaker. Before using, check the sides and bottom of the can to make sure all the pigment has been mixed in. If mixing is going to be done with a wooden paddle or an electric drill mixer, pour off half of the liquid from the top of the can...
Open the catalog to page 2All Pettit catalogs and brochures
-
SeaGold Data Sheet
2 Pages
-
SeaGold Premium Wood Finish
1 Pages
-
Pontoon Pro
2 Pages
-
Neptune5
2 Pages
-
Hydrocoat SR
2 Pages
-
Horizons®
2 Pages
-
SC - 21
2 Pages
-
Paste Wood Filler Stains
1 Pages
-
Color Card
6 Pages
-
Ultima SR-40
2 Pages
-
Hydrocoat
2 Pages
-
Dark Mahogany 7665
1 Pages
-
Hi-Build Varnish 2056
2 Pages
-
Flagship 2015
2 Pages
-
Captain's 1015
2 Pages
-
Sealers
2 Pages
-
EZ Cabin Coat
2 Pages
-
EZ Bilge
2 Pages
-
EZ Decks
2 Pages
-
Boot Top Enamels
2 Pages
-
Shipendec Enamels
2 Pages
-
Easypoxy
2 Pages
-
Underwater Metal Kit 6456
2 Pages
-
Sandless Primer 6999
2 Pages
-
Tiecoat Primer 6627
2 Pages
-
Skip Sand Primer 6998
2 Pages
-
Aluma Protect 4400/4401
2 Pages
-
Pettit Protect 4700/4701
2 Pages
-
95 Fiberglass Dewaxer
1 Pages
-
Brushing Thinner 120/T-10
1 Pages
Archived catalogs
-
Products brochure
14 Pages