Catalogue-reservoirs-nauta-uk
1Pages

{{requestButtons}}

Catalog excerpts

Catalogue-reservoirs-nauta-uk - 1

FOR WATER Our most popular application is also the easiest way to increase or replace water capacity on boats whose tank is inadequate or deteriorated. NAUTA® flexible water tanks use an exclusive Tedlarf inside lining to maintain a taste-free system most PVC, fiberglass, other plastics and metal contribute a distinct, unpleasant flavour to fresh water, Tedlarl does not. No venting is required for water tanks; only a fill pipe and a simple draw line to head and / or gallery pumps. 5 years warranty coverage. Starboard and port tanks In order to prevent the tanks from emptying into one another, a needle valve is place at the center point of the pipe connecting the tanks. ADDITIONAL FITTINGS penneL & fupo THE FLEXIBLE TANK We have designed a comprehensive range of nylon fittings to be used only on NAUTA® tanks. Each type of fittings is composed of 3 parts which ensure together with the rubber seal and the rubber coated fabric a complete tightness. The necessary fitting for self-installation at the most suitable location on the tank wall. Generally, vent fittings are required on holding or gas tanks (not required on water), should be positioned at the higher end of the tank, while draw fittings are best located at the lower end. Under no condition should fittings be installed on the bottom side of the tank. All fittings should be installed on the bottom side of the tank. All fittings should be installed in the top half of the tank and not closer than 4” to the edge and not through a seam doubler. The technique of storing and transporting liquids through the use of flexible tanks has many advantages : • lightness • handiness • adaptability • fiability NAUTA® FLEXIBLE TANKS provide many advantages over rigid tanks and have therefore, become very popular with both yacht-builders and boat owners. Each of these tanks uses an extremely rugged 935-dtex nylon fabric, coated on both sides with a neoprene / nitrile compound. FiMing from the highest point Allows any air to escape that might have entered during the filling. Pumping should be done just above the lowest point, which is the highest water level. For a vertical positionned tank The tank must be maintained empty by its eyelets. Once filled, the tank is held in place by the walls surrounding it, and thus is no longer free. Installation of nipples is done in the same manner as for rigid tanks. FOR HOLDING : A SOLUTION FOR POLLUTION The more rigorously enforced laws against overboard discharge now make non-compliance extremely costly. A NAUTA® flexible holding tank, on the other hand, provides a relatively inexpensive Type III solution. In addition, the Teldad lining of these NAUTA® tanks prevents gas permeation, thus stopping a major odour problem with many other holding tanks. Combined with a few other components, this solution is both legal and far less costly than replumbing a vessel or installing a more complex and expensive Type I or Type II system : it occupies less space and requires no electrical power. FOR DIESEL BIG CAPACITY GAS TANK NAUTA® flexible gas tanks can dramatically extend the range of powered sail and motor boats. They can be deck or cockpit mount to gravity feed (or be hand-pumped) to tankage below decks. And, when empty, these tanks can be rolled up and stowed. Sport and commercial fishermen heading into offshore waters and cruisers visiting remote ports (where refuelling may be unavailable or of suspect quality) will find these NAUTA® tanks an ideal, low cost solution. NAUTA® gas tanks of 200 litres capacity and larger are supplied with adjustable hold-down straps with D-rings. Two N.P.T brass fittings allow this system allow this system to connect with conventional fuel line. 1 year warranty coverage PORTABLE GAS TANK NAUTA® flexible portable tanks are a remarkable improvement over the traditional painted metal tanks. Perhaps the most noticeable change : they do not live rust rings on the floorboards or cockpit sole. These roll-up when empty tanks offer convenience in use and in stowage. They are also more comfortable to carry than most rigid tanks. They do not rust, will not scrape your paint, are easier to tie down and do not rattle when you are underway. 1 year warranty coverage Filling and pumping from above the tank When the tank is free and flat, pumping is done by suction. There is no air in the flexible tank. Straight nipples are used for flexible pipes arriving vertically. Filling and pumping with a bent nipples (45°) For flrxible pipes arriving horizontally. Installation of two or more tanks at the same level Each tank is connected directly to the pump and the drain with the aid of tees (parallel installation). Pumping through the filling circuit Connect the tee piece (35 mm x 15 mm x 35 mm) to the O 35 mm flexible pipe at the base of the tank. Join the 015 mm Heavily lapped seams are inside-reinforced with a “doubler” to provide extra strength. All NAUTA® tanks are vulcanised to assure leakproof panels and seams for years of trouble-tree service. All are covered by a warranty Because of their flexibility and the NAUTA® range of sizes, these tanks can fit into almost any space, especially those odd-shaped places that would otherwise be wasted. NAUTA® tanks are very easy to work with. Several for water and holding are available with fittings already installed. But NAUTA® 's construction allows custom placement of fittings to suit your particular requirements and makes it simple to install them (see fittings). NAUTA® - Tanks for fresh water and drinking water FITTING THE CONNECTIONS Fitting of the connection is generally made on the same side of the tank. The position of the nipple will be so that there will be a minimum margin of 100 mm between the connection and the edges of the tank. Use the washer (see drawing) to mark out the circumference of the hole to be made in the support. Its dimension must be the one of the washer inside. Then cut with scissors the marked out hole and take care to separate the two walls of the tank in order to avoid to damage the opposite wall when cutting. it is also necessary to take care not to make a hole of a bigger diameter then the one made in ref. 2. Bring the edges of the hole nearer by pinching the fabric and introduce the base of the nipple as a button in a button-hole. Place the washer with the edge on fabric side (in order to ensure the imperviousness) and then the screw ring. Tighten the ring with the wrench. Check the tightening periodically and in particular some days after the fitting installation. RUBBER SEAL MAINTENANCE NAUTA® flexible tanks used for drinking water will operate more satisfactory if the following procedures are observed. Before putting in use for the first time, partly fill the tank with warm water (50°c) and a 1% solution of mild detergent. After a few minutes, rinse with clear water and fill it again with water treated with chlorine tablets (follow package instructions for a 5% concentration). Empty after 2 hours and carefully and thoroughly rinse with clear water. These cleaning operations should be performed with the system fully installed so that all the piping undergoes the same treatment. When the tank will not be used for a long period (winter layup...), keep it partly filled with water and 10% of chlorine solution. Because it is not possible to completely evacuate the tank, this procedure best prevents the development of microorganisms which could coat the inside and contribute to a bad taste in water. Before returning the tank to service, follow the same procedure as used with a new tank. Even if using your tank constantly, this cleaning operation is recommended at 6 months interval. Do not forget that the pipes also contribute to the water's taste and should be involved in the regular cleaning process. NAUTA® - Gas Tanks & used water holding tanks NAUTA® - Portable Gas Tanks for Outboard Motors PGnnGL & FUPO Boulevard de I'Eurozone 102 - 7700 Mouscron - Belgique - Tel. + 32 56 39 21 00 - Fax : + 32 56 39 21 01 E-mail : orca@orca.eu - Web site :

Open the catalog to page 1

All ORCA / Pennel & Flipo catalogs and brochures

Archived catalogs

  1. Orca Boom

    10 Pages