Catalogs >
Northern Lights >
M150C13 Specification Sheet

M150C13 Specification Sheet
1Pages

Catalog excerpts

Features and Specifications Engine Block • Six cylinder, four cycle, in-line, liquid cooled, overhead valve, marine diesels based on heavyduty industrial engine blocks. • Balanced, forged crankshaft with induction hardened journals and rolled fillets for long life. • Replaceable, wet cylinder liners for long life and low rebuild costs. • Bimetallic valves with chrome stems and rotators. • Replaceable valve seats and guides. • Three ring aluminum alloy pistons with Ni-Resist insert for the top ring. Keystone piston ring reduces carbon buildup under light loads. • Torsional crankshaft dampers help ensure smooth operation. • A single poly-vee drive belt powers the alternator and jacket-water pump. Fuel System • High pressure common rail fuel injection for smooth, clean delivery. • Direct fuel injection systems • Ring clamp fuel lters with air bleed and drain. • Electric fuel pump integrated into primary fuel filter. Computer controlled priming for ease of operation. Lubrication System • Positive displacement gear-type oil pump. • Full ow, spin-on oil lter. • Jacket-water, plate-type, full ow oil cooler reduces heat and prevents lube oil breakdown. • Large capacity oil pan. • A closed loop crankcase vent traps oil vapor to keep the engine room clean. • Dry air lter silences intake noise. • Turbocharger with jacket water cooled turbine housings for safety. • Jacket water aftercooler provides optimized combustion and output. No second keel cooler needed. Cooling System • Keel cooled with heat exchanger option • Gear driven, belt-less sea water pump with flexible impeller made of bronze and stainless steel. • Cast iron expansion tank with brass ller neck. • Two thermostats for quick warm-ups and safety. • Cast-iron exhaust manifold for reliable temperature control. • Negative ground, 12 volt DC system has circuit breaker, starter motor and alternator with regulator. Relay board and senders for gauged panels standard. • Standard S-3C remote control panel with engine hour meter, coolant temperature gauge, oil pressure gauge, DC voltage meter, start-stop and shutdown bypass switches. Additional optional panels help you specify the amount and type of information delivered. • Low oil pressure and high coolant temperature safety shutdown system. • Direct coupled, single bearing, 12 lead, reconnectable AC generator. Maintenance free brushless design. • All NL generators meet or exceed class society standards with Class “H” insulation, accessible diodes, oversized ball bearings, marine grade shafts and conservative 90°/50° heat rise ratings. • Engines and generators are torsionally matched for long life. • Automatic voltage regulator; ±1.5% regulation over the entire range from no load to full load. • Configured for 0% isochronous droop with integral electronic governor control supplied by ECU. Voltage regulation Frequency droop control Phase and power factor Generator full load temperature rise Lugger Diesel Engine Data Inline cylinders/aspiration/operating cycle Displacement - cid (liter) Bore/stroke - inches (mm) Fuel injection pump type and control Cooling System (Keel cooling standard, heat exchanger optional) KC Heat rejection to jacket water -1800 rpm BTU min KC Freshwater pump capacity - 1800 rpm/gpm (lpm) KC Approximate cooling capacity - gal (ltr) KC Coolant Flow - 1800 rpm/gpm(lpm) KC max seawater pump suction head lift - ft (m) KC sea water pump inlet hose ID - in (mm) KC min. seawater inlet/discharge thru-hull - in (mm) DC Electrical (12V standard, 24V optional) DC starting voltage - standard (optional) Min battery capacity - amp hr/12V CCA (24V CCA) Starter rolling amps @ 0°C - 12VDC (24VDC) 12 Volt battery cable size up to 10 ft (3m) Air Air consumption - 1800 rpm/cfm (m3/m) Approx heat radiated to air - 1800 rpm/BTU/min Generator cooling air flow 1&3Ø - 1800 rpm cfm Exhaust gas volume - 1800 rpm/cfm (m3/m) Exhaust gas temp - 1800 rpm/F° (C°) Max. exhaust back pressure - inch H2O (mm H2O) Wet exhaust elbow OD- in (mm) Dry exhaust elbow in (mm) Fuel Fuel injection pump type and control Min suction - in (mm) Min return line - in (mm) Max fuel transfer pump suction lift - ft (m) Max fuel flow to transfer pump at 1800 rpm - gph Specific fuel consumption max load 1800 rpm - lbs.hp.hr Approx. fuel rate3 at 1800 RPM full load - gph (lph)3 Max Engine Operating Angle Continuous (with separate expansion tank) Intermittent (2 minutes) Dimensions and Weight* Length - inches (mm) Width - inches (mm) Height - inches (mm) Weight - pounds (kilograms) * Dimensions provided for information only. Do not use for installation. Contact factory for installation drawings and info. Information and dimensions subject to change without notice. Northern Lights and Lugger are registered trademarks of Northern Lights, Inc. © 2014 All rights reserved. Litho USA. S156 11/14

Open the catalog to page 1