staybond epoxy glue

Product catalog summary

Description: Staybond Epoxy Glue is a non-staining, high-strength, two-part epoxy adhesive suitable for gap filling. It is designed for waterproof structural applications in boatbuilding and laminating, and can bond materials like fibreglass, metals, concrete, ceramics, and glass.

Properties: At 20°C, the glue is a translucent cream with a non-staining, light amber finish. It has a coverage of 1m² per mixed litre at 1mm thickness, a pot life of 30 minutes at 50% relative humidity, and a full cure time of 7 days. The mixing ratio is 1:1 by volume, and it should not be thinned. The product is non-volatile and has a storage life of at least 5 years if sealed properly.

Preparation: For timber, remove contaminants and sand at 45 degrees to the grain. Use acetone or methylated spirits for cleaning. For oily timbers like teak, use NORGLASS Acetone and apply glue within 20 minutes. Other surfaces should be sandblasted or solvent cleaned.

Application: Mix equal volumes of base and hardener thoroughly until a creamy paste is achieved. Do not alter the mixing ratio or add extenders. Prewarm components in cold weather before mixing.

Precautions: Avoid gluing below 10°C. Ensure proper ventilation and avoid skin and eye contact. If adverse reactions occur, seek medical advice. The hardener deteriorates quickly if exposed to air.

First Aid: In case of poisoning, contact a doctor or Poisons Information Centre. Do not induce vomiting; provide milk or water.

Special Instructions: Cramping times should be at least 48 hours at 20°C. Avoid starving joints of glue by over-cramping. Complies with British Standards 1204 parts 1 & 2 for water and boil proof criteria.

Contact Information: NORGLASS Laboratories Pty Ltd, 59 Moxon Rd, Punchbowl NSW 2196, Phone: 02 9708 2200, Email: [email protected]

Catalog excerpts

May 2010 PRODUCT DATA SHEET STAYBOND EPOXY GLUE DESCRIPTION: A non staining gap filling, 2 pack epoxy adhesive of exceptionally high strength and cohesive value. USES: As a waterproof, structural glue for boatbuilding and laminating work. Also used for bonding fibreglass, metals, concrete, ceramics and glass to themselves or to dissimilar materials. PROPERTIES (At 20°C) ° COLOUR: Translucent cream TOXICITY: See Precautions FINISH: Non staining, light amber COVERAGE: 1 mixed litre = 1000cu.cm. (1 mixed litre will cover 1m² at 1mm thick) DRYING TIME: Workable after 24 hours. Full cure 7 days RECOATING: N/A POT LIFE: 30 minutes at 50% relative humidity (subject to mass). Storage life minimum of 5 years if correctly sealed. NOTE: The hardener deteriorates quickly if not sealed properly. MIXING RATIO: 1:1 by volume. THINNING: NOT BE THINNED UNDER ANY CIRCUMSTANCES. WEIGHT/LITRE: 0.95kg when mixed VOLUME SOLIDS: Exceeds 99% FLASH POINT: Non volatile CLEAN UP: NORGLASS EPOXY THINNER U.N. NUMBER: FREE

Open the catalog to page 1

Page 2 – Staybond Epoxy Glue PREPARATION TIMBER: OTHER SURFACES: Remove all forms of grease, oil, water or other contaminants. Sand timber at 45degrees to the grain. Vacuum off all sanding dust from the grain. This is essential for adhesion. Wipe over the surface to be glued with Acetone or Methylated spirits on a clean cloth and allow to dry. Oily timbers such as teak should be wiped down with NORGLASS ACETONE to remove surface oils, and be coated with STAYBOND EPOXY GLUE within 20 minutes. If left too long, more oil will rise to the surface of the timber reducing the overall adhesion. All other...

Open the catalog to page 2

staybond epoxy glue

staybond epoxy glue

Catalog excerpts

All Norglass catalogs and brochures