NORDHAVN 41
36Pages

Pacific Asian Enterprises, Inc. 25001 Dana Drive, Dana Point CA 92629 (949) 496-4848 phone NORDHAVN 41 STANDARD SPECIFICATIONS GENERAL DIMENSIONS* *Dimensions are subject to change with Buyer’s selected options and personal effects which may add to displacement and increase both draft and waterline length LOA: 41'- 41/4” (12.60 m) LWL: 40-'0" (12.19 m) BEAM: 13'- 11” (4.24 m) BEAM W/L 13’-4 1/2” (4.08m) DRAFT: 4’ 6 ½ " (1.38 m) DISPLACEMENT: 43,300LBS, 19.2 LT, 677CU. FT. (19.5 METRIC TONS) WATER CAPACITY: 300 GALLONS (1,136 LITERS) FUEL CAPACITY: 900 GALLONS (3407 LITERS) HOLDING TANK CAPACITY: 70 GALLONS (265 LITERS) GRAY WATER CAPACITY: 70 GALLONS (265 LITERS) A/B RATIO: 1.90/1 BASIC STRUCTURE Builder to utilize the latest vacuum bagging and resin infusion techniques on all main structures in order to save weight and increase strength 1. HULL LAMINATION schedule per construction plan A. Metyx brand multiaxial fabrics for composites and Sisecam brand glass fibers B. Skin Coat: DSM ATLACK 580 ACT Hi TG (132 C degree) Vinyl ester resin C. General laminating resin: DSM Synolite 0288-L-1 (Hi TG Resin) D. Gelcoat: Bufa İSO/NPG spray type, BÜFA®-Marine NPG-Gelcoat-S 2. DECK LAMINATION schedule per construction plan A. Metyx brand multiaxial fabrics for composites and Sisecam brand glass fibers B. Skin Coat: DSM ATLACK 580 ACT Hi TG (132 C degree) Vinyl ester resin C. General laminating resin: DSM Synolite 0288-L-1 (Hi TG Resin) D. Gelcoat: Bufa İSO/NPG spray type, BÜFA®-Marine NPG-Gelcoat-S 3. Core: Gurit, Airex or Diab Balsa Core A. Cabin side (vertical surfaces) Balsa Core B. Cabin top and deck (horizontal surface) Balsa Core C. Hull

4. DECK/HULL JOINT: A. Between deck and hull flange: Crystic Crestomer 1152 urethane acrylate adhesive B. Inside of joint: Two (2) layers mat and woven roving C. Mechanical fastening: 5/16" (6.35 mm) x 20unc thru bolt on 6" (15.2 cm) centers where accessible. In areas that cannot be accessed self-tapping machine screws used 5. LONGITUDINAL STRINGERS A. Hull: port and starboard, engine beds, and floor stringers B. Deck: per design 6. INTERIOR TRANSVERSE FLOORS: Per design w/ foam core 7. BALLAST: Internal weight 4000 lbs (1814 kg) - glassed in place 8. HULL COLOR - Pebble Gray # RAL 7032 A....

9. BOTTOM PAINT (Black) A. Two (2) coats Sea Hawk epoxy barrier coat B. Three (3) coats of Sea Hawk AF33 anti-fouling paint STANDARD MACHINERY DETAILS 1. ENGINES- Betamarine 85 x 2 Kubota Model: BV3600 base engine, 4 cylinder 75 bhp @ 2800rpm 70amp 12v alternator heat exchanger cooling, white poly urethane paint finish, EPA certified Tier 3, EU Compliance 2013/53/EU BETA 85T Specifications A. Transmission: standard - PRM750D 3.942:1 offset straight reduction gear x 2, PTO for hydraulics on one transmission, soft shift, painted to match the engine B. Engine instrument panel: deluxe with...

2. PROPELLER SHAFT: 1 ¾” (5.1 cm) diameter stainless steel x 2, A22 or equivalent A. Standard S.A.E. double taper 3. PROPELLER STRUTS: x 2 V shaped struts per PAE design. A.316 stainless steel B. Cutless bearing Dura Max 4. PROPELLER: 4-bladed bronze, 28" diameter x “pitch (cm d x cm p) x 2 counter rotation 5. STERN TUBE: FRP A. Stuffing box: Tides Marine  ABS and Lloyds Type Approval. 6. FUEL FILTERS: Single Racor 900 MA plus engine mounted filters x 2 UL classified in accordance with ISO 11088 for CE systems RACOR Information Packet 7. WET EXHAUST 8. ENGINE COOLING SYSTEM: Filled with...

10. ENGINE ROOM FINISH: Molded FRP engine beds and floors, insulated with Technicon or equivalent fire proof foiled and leaded foam 2"(5.08 cm) thick. All exposed insulated surfaces lined with perforated anodized aluminum 11. ENGINE ROOM BLOWERS: Delta T Systems Ignition protected 11 Inch (279.4) DC Axial Fans with flow rates to 1424 CFM (2419 m3/h) 12 Volt DC -• Part No. 500-311122IP x 2 A. CE Labeled and conforms to J1171, ISO 8846 and ISO 9097 Delta T Spec Sheet 12. STABILIZERS: ABT 220 stabilizer with 6 Sq. Ft. fins

A. New TRACLink control panel 13. SIDE POWER BOW THRUSTER A. Side Power SE Series STEERING SYSTEM 1. HYPROMARINE Electronic Command Steering consisting of the following components: A. HM5290/12 ECS Power Unit - 12V B. HM5160 - ECS Helm Unit Front Mount C. HC5319 - I/B Cylinder BA175 7TM D. HM5750 - Bypass Valve E. Tie rod F. HM5195/15 ECS Wiring Harness Assembly 15m G. Bypass valve for emergency tiller steering

HYPRO Steering Manual 2. HYDRAULIC LINES: Eaton brand 3. BY-PASS VALVE for emergency tiller steering

5. EMERGENCY TILLER: Attached to top of starboard rudder post via inspection port and stows in lazerrette 6. RUDDERS: Stainless steel plate style x2 A. Rudder stock: 2" (3.81 cm) A22 or equivalent stainless steel B. Rudder shelf: Molded FRP C. Tides Marine Tube system including bearings and lip seal PLUMBING SYSTEM 1. WATER TANKS: A. Number and capacity: One (1) tanks totaling 300 gallons (1,136 liters) B. FRP construction 2. FUEL TANK: A. Number and capacity: Two (2) tank totaling 900 gallons (3407 liters) B. FRP Construction C. Inspection plate appropriately positioned for interior access...

3. FUEL PIPE AND HOSE: A. Supply line from tank to supply reservoir is 3/4" (1.9 cm) I.D. with Vetus brand FUHOSE10A fuel hose and reusable fittings

B. Fuel lines from supply reservoir to engines are 1/2" (1.27 cm) I.D. with Vetus brand fuel hose and reusable fittings C. Fuel line from supply reservoir to optional generator 1/2" (1.27 cm) I.D. with Vetus brand fuel hose and reusable fittings D. Vent lines are fuel certified A1 or A2, reinforced hose 1" (1.9 cm) I.D. E. Tank fill lines are fuel certified A1 or A2 reinforced hose 1-1/2" (3.81 cm) ID 4. WATER HOSES: A. Cold water: blue 1/2" (1.27 cm) diameter Whale brand tubing system or equivalent with all Whale fittings B. Hot water: red 1/2" (1.27 cm) diameter Whale brand tubing with...

C. Sea water hoses: Vetus reinforced rubber certified for marine use and provided with double stainless steel clamps below the water line D. Fresh water fill hose to be Vetus brand hose Size: Colors: Trident Vac X.H.D. Sanitation Hose #148 Extra heavy-duty sanitation hose of smooth white vinyl. Specially compounded to provide excellent resistance to odor permeation and (FDA) potable water fill. Also for critical bilge, drain scuppers, live wells, etc.. Hard PVC helix gives good flexibility and bend radius. No cuffs required.* Don't use with alcohols, anti-freeze, petro-chemicals or...