User manual Ningbo SHANBEI Technology Co.,Ltd

Warning: Before using this product, please refer to the important safety information in the user manual and review all warnings, limitations and disclaimers. This product is no substitute for proper training and careful seamanship. Proper installation and proper use of the equipment is the responsibility of the owner to avoid accidents, personal injury or property damage. The user of this product is solely responsible for compliance with maritime safety practices. The owner is solely responsible for installing and using the equipment in a manner that will not cause accidents, personal injury...

Product appearance • • Product composition • Product size drawing * Product wiring diagram

The WSS-R270 rudder Angle feedback is installed in the rudder compartment and is used to convert the mechanical Angle of the rudder into an electrical or digital signal in real time and transmit it to the receiving module, such as the rudder Angle indicator and the rudder Angle distributor. The product uses standard potentiometer output, CAN also use digital CAN bus output, has the advantages of long communication distance, strong anti-interference ability. The product adopts the lever transmission structure to ensure the reliability of the steering gear transmission. The internal gear transmission...

1. The feedback shell is made of ABS engineering plastic, the main shaft is made of stainless steel, and the internal transmission is made of copper gear; 2. Resistance tolerance of potentiometer ±10%, independent linear tolerance 1.0%; 3. Output mode: direct potentiometer linear output, linear relationship with the scale, the theoretical output is shown in the figure below, the actual output is seen in the product factory inspection report.

1. The format of can is standard frame, baud rate: 100K; buff [0] 8 bits higher after lOx Angle enlargement; buff [1] Low 8 bits after lOx Angle enlargement; Tape symbol For example: left rudder 36.3° : Oxfe; 0x95 Right rudder 15.7° : 0x00; 0x9d 2. The format of RS422 is $AGRSA,XXXR*hh<CR><LF>, where XXX is the value after the current Angle is expanded by 10 times, which can be compared with the display value of the digital tube; R is the right rudder Angle, L is the left rudder Angle.

The rudder Angle feedback should be flexibly installed according to the type of steering gear, fixed with M8 triple combination screws and nuts, and connected with a threaded rod to form a parallelogram connecting rod structure to ensure that the rotation Angle of the rudder is equal to the rotation Angle of the feedback rod. 1. Installation of tilting cylinder steering gear rudder Angle feedback device: tilting cylinder steering gear rudder Angle feedback device is suitable for installation on the front and rear side of the rudder rod, please adjust according to the specific layout and position...

1. After installation, check whether the protection is reliable. If only one waterproof joint is used, the other should be kept sealed. 2. Switch on the power supply, manually hit the rudder, compare the rudder Angle feedback value and the scale value of the hydraulic steering machine, and constantly adjust the extension length of the dial rod and the length of the connecting rod to ensure 1 to 1 transmission.

This product has been put into operation since the use, basically no fault, with our statistics, the after-sales problem is basically due to wiring errors, resulting in normal use, in addition, there is no technical fault. Customers in the use of the process, if you find technical problems, please promptly communicate with our technical personnel.

6.1 Safety protection devices and precautions 1. The important position of this product has been tightened seal processing at the factory, shall not be disassembled without permission, if the seal is damaged, any product quality problems are borne by the buyer. 2. Once the product fails to operate normally, please stop using and disconnect the power supply immediately, and contact our after-sales service engineer for a solution. 6.2 Troubleshooting procedures and methods 1. In the process of use, there is an unsolvable fault problem, contact our after-sales service engineer. 2. During the warranty...

7.1 Daily maintenance and maintenance In the daily non-use state, attention should be paid to the maintenance of this product. Through maintenance, maintenance can improve the service fife of the product, the specific maintenance and maintenance methods are as follows: 1. Wipe the surface of the product regularly with a dry rag to ensure that the outside of the product is clean and tidy. 2. Regularly check the lubrication of fisheye bearings and other parts, and apply appropriate grease. 1. Stop using the device when there is a problem. Contact our after-sales engineer. 2. The input voltage shall...

Physical damage to the product caused by violent shaking and collision should be avoided during transportation. Room temperature, dry, cool environment. The warranty period of this product is 12 months from the date of receipt of the goods by the buyer. Based on the date of receipt of documents for express delivery or the date of receipt of invoice.

9.1 Phone number of the after-sales engineer Manufacturer: Ningbo SHANBEI Technology Co., LTD Address: A2-902, R&D Park, High-tech Zone, Ningbo Postal Code: 310001 Tel: (0574) 87182781 Fax: (0574) 87182781

For more information, please visit: www.shanbei-tech.com Ningbo SHANBEI Technology Co.,Ltd Add: 902 Area A, R&D Park, High-tech Zone, Ningbo, Zhejiang, China Tel: 0574-87186781 /18067343163