User manual Ningbo SHANBEI Technology Co.,Ltd

Warning: Before using this product, please refer to the important safety information in the user manual and review all warnings, limitations and disclaimers. This product is no substitute for proper training and careful seamanship. Proper installation and proper use of the equipment is the responsibility of the owner to avoid accidents, personal injury or property damage. The user of this product is solely responsible for compliance with maritime safety practices. The owner is solely responsible for installing and using the equipment in a manner that will not cause accidents, personal injury...

The WSS-H76 heading sensor is mainly used to detect ship heading value in real time. Through the built-in 9-axis electronic compass and high-precision GPS module, the stable heading value can be obtained and converted into the standard NMEA0183 data protocol output to the automatic rudder, radar, AIS and other equipment that needs to direct data. At the same time, it can output longitude, latitude and inclination data, with stable and reliable, easy to use, small size and so on. The product can also be used with the company's rotary compass repeater and signal distributor to display, distribute...

Outline dimensional drawing

1. Rotate the main body to the 1m support rod as shown in Figure 3.1 (it is strictly prohibited to use ferromagnetic materials, non-metallic materials must be used, such as bamboo pole, wooden pole, glass fiber reinforced plastic, etc.), and fasten it with tight screws. 3. As shown in FIG. 3.3, fix the pole and sensor of Part B on the fence of the compass deck to ensure that it is fixed firmly and reliably, without rocking or loosening. Keep it flush with the deck plane and install it in the center of the ship as far as possible. Installation procedure diagram

1. Install and secure it as required. 2. Insert the aerial plug of the antenna into the heading divider (our model WCU-0308), you can obtain a stable heading digital value (standard NMEA0183 signal, HDT statement) and send it to radar, AIS, autopilot and other equipment; The compass repeater (our model WSI-H192A) can also be inserted to display the current heading value in real time. 3. If the device is connected to another device, cut off the plug and connect cables according to the cable definition. You are advised to use a fork or round cord end terminal. 4.2 Matters needing attention 1. If...

This product has been put into operation since the use, basically no fault, with our statistics, the after-sales problem is basically due to wiring errors, resulting in normal use, in addition, there is no technical fault. Customers in the use of the process, if you find technical problems, please promptly communicate with our technical personnel.

6.1 Safety protection devices and precautions 1. In the important position of this product, the fastening seals have been processed before leaving the factory, and shall not be disassembled without permission. If the seals are damaged, any product quality problems will be borne by the buyer. 2. Once the product fails to operate normally, please stop using and disconnect the power supply immediately, and contact our after-sales service engineer for a solution. 6.2 Troubleshooting procedures and methods 1. In the process of use, there is an unsolvable fault problem, contact our after-sales service...

7.1 Daily maintenance and maintenance In the daily non-use state, attention should be paid to the maintenance of this product. Through maintenance, maintenance can improve the service fife of the product, the specific maintenance and maintenance methods are as follows: 1. Wipe the surface of the product regularly with a dry rag to ensure that the outside of the product is clean and tidy. 1. Stop using the device when there is a problem during operation. Contact our after-sales engineer. 2. The input voltage shall be carried out in strict accordance with the wiring instructions. Failure to operate...

Physical damage to the product caused by violent shaking and collision should be avoided during transportation. Room temperature, dry, cool environment. Avoid high temperature exposure or low temperature freezing, which will cause irreversible damage to the damping parts and reduce the service life. The warranty period of this product is 12 months from the date of receipt of the goods by the buyer. Based on the date of receipt of documents for express delivery or the date of receipt of invoice.

9.1 Phone number of the after-sales engineer Manufacturer: Ningbo SHANBEI Technology Co., LTD Address: A2-902, R&D Park, High-tech Zone, Ningbo Postal Code: 310001 Tel: (0574) 87182781 Fax: (0574) 87182781

For more information, please visit:Ningbo Shanbei Technology Co.,Ltd Address: 902 Area A, R&D Park, High-tech Zone, Ningbo, Zhejiang, China WhatsAPP: +86 13186888051 E-mail: [email protected] Wechat: 13186888051