User manual Ningbo SHANBEI Technology Co.,Ltd

Warning: Before using this product, please refer to the important safety information in the user manual and review all warnings, limitations and disclaimers. This product is no substitute for proper training and careful seamanship. Proper installation and proper use of the equipment is the responsibility of the owner to avoid accidents, personal injury or property damage. The user of this product is solely responsible for compliance with maritime safety practices. The owner is solely responsible for installing and using the equipment in a manner that will not cause accidents, personal injury...

7.3 Long-term maintenance and maintenance 8 Transportation, storage and warranty

The WSI-H192A compass repeater is a device that can accurately and real-time feed back the ship's heading information to the steering control room. The size of this product adopts standardized design and can freely choose desktop installation or embedded installation according to the actual situation. The product has the following characteristics: 1. Beautiful and simple; Quiet, high precision; 2. Touch button, easy to operate. Product appearance drawing

Table mounting hole dimensions 1.5 Product wiring diagram Product appearance drawing Power Electronic compass Extend 1. The device is delivered with two cables: two-core cable and four-core cable. 2. Connect the 2-core cable to the power socket with the red terminal of the cable and the black terminal of the cable to the 24V negative terminal, as shown in Figure 1.3. 3. Insert the 4-pin plug of the electronic compass into the center socket. 4. If you need to output heading signals to other devices, plug the four-core cable into an expansion socket. Otherwise, do not use the socket. (Four-core...

1. As shown in Figure 3.1, install the fixing frame A on the back of the compass repeater by screw C. 2. Secure the compass repeater to the mounting surface by screw B to ensure stability. Installation procedure diagram

1. Power on: Ensure that the device is properly connected and the power button is back bright. Press the power button to power on and the compass repeater enters the automatic position seeking state. If no electronic compass or other heading source is connected, ERR is displayed on the digital display screen in the lower left corner, indicating that no heading source is connected or the heading source is abnormal. 2. Shutdown: Press the power button for 4 seconds and release the finger, the machine will enter the standby state; 3. Brightness adjustment: in the startup state, press the brightness...

This product has been put into operation since the use, basically no fault, with our statistics, the after-sales problem is basically due to wiring errors, resulting in normal use, in addition, there is no technical fault. Customers in the use of the process, if you find technical problems, please promptly communicate with our technical personnel. 1. If the backlight is not on after the device is powered on, check whether the power supply is normal. 2. Digital tube display ERR, check whether the heading source is normal; 3. Touch the key does not respond, the key is damaged; 4. The compass does...

6.1 Safety protection devices and precautions 1. In the important position of this product, the fastening seals have been processed before leaving the factory, and shall not be disassembled without permission. If the seals are damaged, any product quality problems will be borne by the buyer. 2. Once the product fails to operate normally, please stop using and disconnect the power supply immediately, and contact our after-sales service engineer for a solution. 6.2 Troubleshooting procedures and methods 1. In the process of use, there is an unsolvable fault problem, contact our after-sales service...

7.1 Daily maintenance and maintenance In the daily non-use state, attention should be paid to the maintenance of this product. Through maintenance, maintenance can improve the service fife of the product, the specific maintenance and maintenance methods are as follows: 1. Wipe the surface of the product regularly with a dry rag to ensure that the outside of the product is clean and tidy. 1. Stop using the device when the compass repeater has a problem. Contact our after-sales engineer. 2. Please strictly follow the instructions. Failure to operate in accordance with the regulations will result...

Physical damage to the product caused by violent shaking and collision should be avoided during transportation. Room temperature, dry, cool environment. Avoid high temperature exposure or low temperature freezing, which will cause irreversible damage to the damping parts and reduce the service life. The warranty period of this product is 12 months from the date of receipt of the goods by the buyer. Based on the date of receipt of documents for express delivery or the date of receipt of invoice.

9.1 Phone number of the after-sales engineer Manufacturer: Ningbo SHANBEI Technology Co., LTD Address: A2-902, R&D Park, High-tech Zone, Ningbo Postal Code: 310001 Tel: (0574) 87182781 Fax: (0574) 87182781

For more information, please visit:Ningbo Shanbei Technology Co.,Ltd Address: 902 Area A, R&D Park, High-tech Zone, Ningbo, Zhejiang, China WhatsAPP: +86 13186888051 E-mail: [email protected] Wechat: 13186888051